You are here: Forums SUVs Isuzu Rodeo Isuzu Rodeo Maintenance and Repair

Isuzu Rodeo Maintenance and Repair

118 messages,  Last post on Oct 06, 2009 at 2:06 AM

You are in the Isuzu Rodeo Forum. Your Hosts are steve_ & tidester

What is this discussion about? Isuzu, Isuzu Rodeo, SUV

Messages Page 8 of 12 1 ... 5 6 7 8 9 10 11 12 Prev Next Last

Go To Msg # Search This Discussion

#69 of 118 Re: 4 Wheel Drive Problem [biggsvaj] by drivertodd Dec 02, 2007 (4:15 pm)
Replying to: biggsvaj (Feb 26, 2007 4:38 pm) Hey, did you ever find the problem in the 4X4 locking problem? I have a 2000 that just started having the problem today. Replies to this message: chawkchad (Dec 11, 2007 8:34 pm) drivertodd (Dec 12, 2007 5:59 am)
#70 of 118 2000 4X4 front not working by drivertodd Dec 02, 2007 (4:22 pm)
My 2000 Rodeos' front wheels will not engage. The front drive shaft does turn but the wheels do not. Are there internal hubs or a solenoid that should lock the wheels in?   Please advise potential fixes
#71 of 118 Isuzu Wizzard by tdickson Dec 10, 2007 (6:12 pm)
Hi Folks, I have a 1999 Isuzu wizzard with a 3.0L turbo diesel engine, the vehicle will crank but will not start. Sometimes it will start but will not run, this only happens in the morning. Once the vehicle is started it will run all day.I replaced the gow plugs checked all the fuses they are ok. what could my problem be   Tyrone
#72 of 118 Re: 4 Wheel Drive Problem [drivertodd] by chawkchad Dec 11, 2007 (8:34 pm)
Replying to: drivertodd (Dec 02, 2007 4:15 pm) If you will, please send me any info that you receive about this problem. My Rodeo started experiencing the same problem about a week ago. It may have started earlier but, it was the first time I needed to engage the 4 wheel drive.   I will push the button to engage the 4 wheel drive, the 4 wheel drive light on the dash flashes but, never fully engages into 4wheel drive. Is this the same problem your receiving?   Thanks,   Chad Replies to this message: drivertodd (Dec 12, 2007 5:59 am)
#73 of 118 Re: 4 Wheel Drive Problem [chawkchad] by drivertodd Dec 12, 2007 (5:59 am)
Replying to: chawkchad (Dec 11, 2007 8:34 pm) The right front shaft lost a retainer clip that keeps the splined plate in contact with the splines on the driveshaft and the shaft moved inward towards the differential. The repair in this case was simple. The splines were filed clean so the plate would slide easily and the retainer clip was replaced which held the driveshaft inposition to transmit torque. When the shaft moved inward it was not in the splines and just spun freely. The 4x4 system gave all the front wheel torque to the spinning wheel and we went no where.   Hope this helps
#74 of 118 Re: 1999 Isuzu Rodeo serpantine belt [brianrichardsm] by steelponies Dec 15, 2007 (9:47 am)
Replying to: brianrichardsm (Dec 01, 2007 11:39 am) Hi, saw your message, had the same issue with my 2002 rodeo with 12k miles. Serp belt with all cracks in it. I did mine myself all I used was a very large screw driver as a prybar on the belt tensioner so I can take the tension off and then slip the belt off. 10 minute job, DIY I made a drawing of the belt and pully setup so I new how it went back on. I would suggest doing that makes it even an easier job. Good luck.
#77 of 118 timing by rhanley Jan 13, 2008 (5:47 pm)
does the #one piston on top before timing a 1999isuzu rodeo 3.2L 6 cylinder
#78 of 118 99 Isuzu Rodeo by antonio5260 Jan 17, 2008 (10:45 am)
99 isuzu rodeo 2wd. My question has two parts to it. One is that my fan (radiator or fan that blows a/c i don't which one really) keeps blowing after my engine has been shut off. It will blow for about 15 seconds or so. However, it usually stays on when i have my air condition (or just air) blowing. So usually to fix the problem, before i turn off the ignition, i shut off the air and it doesn't do it. But in the morning, regardless if i turn the air off, it still does it. The second thing is also in the morning when i first turn on the rodeo, the RPMS stay high while changing the gears (it's a standard), this happens for about a good 5-10 minutes i guess while the engine warms up, then i can change gears and they stay where they're supposed to be. I just wanted to know if anyone can help me out or give me ideas as to what the problem might be before i take it into a mechanic. Thanks a lot.

Messages Page 8 of 12 1 ... 5 6 7 8 9 10 11 12 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums SUVs Isuzu Rodeo Isuzu Rodeo Maintenance and Repair