You are here: Forums Pickups Ford Ranger Ford Ranger Transmission Questions

Ford Ranger Transmission Questions

215 messages,  Last post on Nov 08, 2009 at 11:25 AM

You are in the Ford Ranger Forum. Your Host is kcram

What is this discussion about? Ford Ranger, Truck

Messages Page 7 of 22 1 ... 4 5 6 7 8 9 10 ... 22 Prev Next Last

Go To Msg # Search This Discussion

#55 of 215 Trasmission by dangerranger20 Nov 01, 2007 (4:41 pm)
Ok I Have a 97 Ranger w/ 2.3l engine and 5 Speed Tranny I just put in a new clutch, Slave cylander, and Pressure plate It worked for a while then it just would not shift into gear while running. Can someone help me?
#56 of 215 2002 Ranger PU stays in gear by ndfeller Nov 06, 2007 (4:59 pm)
I have a 2002 ford ranger pu at times when I put it in reverse and back up I push in the clutch and it keeps going I have to shut off the engine to get it out of gear, I already replaced the clutch, no help.   HELP Any ideas ????????
#57 of 215 95 Ranger Not going in Park by chapinjohn Nov 09, 2007 (2:33 pm)
Today as I parked (XLT 4.0 automatic) and attempted to put the gear selector in Park and the truck eased forward. I turned off the ignition and now it will not turn over. The gear selector will go into the Park position (and out of park by pressing the brake pedal ) but the truck can be pushed forward so its not in park. I crawled under and moved cable back and forward. Problem evidently isn't there. Ignition seems okay, on and off checks the power door locks. Is there a sensor or relay I should look at? Replies to this message: chapinjohn (Nov 15, 2007 8:12 pm)
#58 of 215 clutch problem by joe159 Nov 13, 2007 (10:41 am)
I have a 91 ranger. yesterday the clutch started poping. I pulled back the carpet and on both sides of the clutch rod the firewall is cracked about 3 inches. What would you do? Replies to this message: bolivar (Nov 13, 2007 11:22 am)
#59 of 215 Re: clutch problem [joe159] by bolivar Nov 13, 2007 (11:22 am)
Replying to: joe159 (Nov 13, 2007 10:41 am) Find a very good welder.
#60 of 215 Transmission or easier fix by emg1981 Nov 15, 2007 (3:48 pm)
So I have a 99 automatic Ford ranger and had some issues that started a month ago. First it wouldn't start so I took the alarm off and it ran again. Now I have to put it in 2nd to get it moving and when it hits about 3000 to 4000 rpms I slip it into drive.... if I drop below 3000 rpms it slips out of gear....and does nothing.... What can I do can someone help?
#61 of 215 Re: 95 Ranger Not going in Park [chapinjohn] by chapinjohn Nov 15, 2007 (8:12 pm)
Replying to: chapinjohn (Nov 09, 2007 2:33 pm) Shift cable broke where it comes near the exhaust, $65 part, fairly easy installation.
#62 of 215 clutch bleeding by cryptic86 Nov 18, 2007 (11:22 am)
I have a 95' ranger 4.0 liter 4x4 5 speed and I just put a new slave cylinder in the transmission. There is an air bubble somewhere but I can not get my coupling off the transmission not to mention I dont have the coupling tool either. so how do i get the coupling off with out the tool, or where can i buy the tool and how much is it?
#63 of 215 Re: do it myself [bolivar] by marty20 Nov 19, 2007 (8:40 am)
Replying to: bolivar (Oct 24, 2007 12:46 pm) Thanks.
#64 of 215 2000 Ranger Trans Slipping by budz2 Nov 27, 2007 (4:51 am)
Im looking to buy a 2000 Ranger from work and the Transmission has a bit of a slip in it, The guy trading it in says that the part to fix it is on backorder. Has anyone ever heard of the 2000 rangers with the 4.0 and auto doing this. I read another post that mentioned a valvebody spacer and another part. I like this truck but dont want to but someone elses nightmare. Thanks in advance Replies to this message: bolivar (Dec 07, 2007 9:38 pm)

Messages Page 7 of 22 1 ... 4 5 6 7 8 9 10 ... 22 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Pickups Ford Ranger Ford Ranger Transmission Questions