You are here: Forums Pickups Ford Ranger Ford Ranger Transmission Questions

Ford Ranger Transmission Questions

215 messages,  Last post on Nov 08, 2009 at 11:25 AM

You are in the Ford Ranger Forum. Your Host is kcram

What is this discussion about? Ford Ranger, Truck

Messages Page 4 of 23 1 2 3 4 5 6 7 ... 23 Prev Next Last

Go To Msg # Search This Discussion

#23 of 215 1992 Ford Ranger: Transmission? by kuberr4 Apr 09, 2007 (2:20 pm)
I have a 1992 Ford Ranger XLT 4x4 5 speed manual. The muffler is off, and at first, it ran fine, but since it has developed a whining, or humming noise. It happens when in 1st, 2nd, 3rd, and overdrive, whether I am accelerating or going at a steady speed, but not when I let off the gas. It doesn't happen in 4th. Also, I sometimes can't shift into first from a dead stop.I am suspecting a bad clutch but am not sure. Anyone know what could be wrong?
#24 of 215 Re: 86 ranger [ahinson] by sirmcannon Apr 20, 2007 (5:20 am)
Replying to: ahinson (Mar 17, 2007 3:19 pm) I had a similar problem with a mystique, it was an electrical problem, the computer puts the tranny in safe mode, thats why it wont go out of 2nd, hope this helps
#25 of 215 ford ranger trans by kdeezle May 18, 2007 (11:20 am)
I am changing the trans in my 91 ranger. It is a 4.0 automatic. to get to the bellhousing top bolts, i have to take out the pipe going into my exhaust manifold. Does anyone know hot to get this out without cutting it off. It is so rusted that i am having a hard time. Does anyone have any tips on getting the old trans out as easy as possible? Replies to this message: rcram (Aug 14, 2009 11:29 am)
#26 of 215 94 Splash Ranger Hydralic Clutch Problems by vasolini May 25, 2007 (8:02 am)
I've replaced all the parts for my clutch from the Master Cylinder, all the way to the pilot bearing. The only part I did not replace is the line from the MC with the male coupling, (it wasn't leaking so I didn't replace it). I can't for the life of me, get the darn thing to bleed out all the air. I have tried for three days to bleed this clutch, then gave up and took it to the shop, where the lead tech has spent three days with the same results, no clutch!! Is there anything I should or can do? Replies to this message: bolivar (May 26, 2007 4:35 pm) vasolini (May 26, 2007 5:46 pm) pistol15 (Jun 01, 2007 6:15 am)
#27 of 215 Re: 94 Splash Ranger Hydralic Clutch Problems [vasolini] by bolivar May 26, 2007 (4:35 pm)
Replying to: vasolini (May 25, 2007 8:02 am) I don't have much advice for you. But I have heard the hydrolic clutch on Rangers can be a real b***h to bleed.   Only thing you might try - a gravity bleed. Just open the lower bleeder, take off/loosen the top cap, and just see if fluid will drain down and move the air out.   Only other guess - call around to other garages to see if you can find one with experience doing a Ranger, one that will say they can successfully bleed one. Replies to this message: vasolini (May 26, 2007 5:46 pm)
#28 of 215 Re: 94 Splash Ranger Hydralic Clutch Problems [bolivar] by vasolini May 26, 2007 (5:46 pm)
Replying to: bolivar (May 26, 2007 4:35 pm) Thanks for your input. They still have the truck and now they are going to pull the tranny to make sure I put everything back together properly. There wasn't much to it, but I told them to go ahead in case there is something I may have done incorrectly. I can't believe it has taken this long and still no good results.  I tried the gravity bleed as per the Haynes manual, but it doesn't flow out, it trickles.  If they can't get it soon, the Ford dealer is right across the street! I prolly shoulda taken it there to begin with. So much for trying to save a buck.
#29 of 215 93 Ford Ranger 4x4 by jack78 May 27, 2007 (7:46 pm)
Why would automatic trans fluid come out the filler tube? When you start the eng to check the trans level it's checks OK (cold). But you drive the truck for just a few minutes then check the level the fluid poors out. I checked the vent tube and blew air in it, it does not seem pluged. The truck has not been driven much. any thoughts?
#30 of 215 Re: 94 Splash Ranger Hydralic Clutch Problems [vasolini] by pistol15 Jun 01, 2007 (6:15 am)
Replying to: vasolini (May 25, 2007 8:02 am) I replaced the clutch in my 95 Ranger and had the exact same problem. I replaced the Master and the slave but still no help until I saw a note in the box the master cylinder came in. The note had me call a help desk and they would walk me through the bleeding process. They had be take the master along with the clutch line off the truck and bleed it by filling the resevoir with fluid and tilting the line while holding the check valve open so the air would come out of the valve. It has been a couple years so the exact steps are a bit fuzzy. I'm pretty confident this will fix your problem. If you still have the master cylinder box, look for the sheet that gives you a 1-800 number and they can help you for free. Good luck.
#31 of 215 91 ranger by kdeezle Jun 02, 2007 (4:12 pm)
I am putting in a auto v6 trans in my ranger. I am a do it mydelfer. any tips on the easiest way to get it in? I am have trouble lining the torque converter up.
#32 of 215 94 Ranger by lk270 Jun 10, 2007 (7:41 pm)
I just purchased a 94 Ranger 3.0 auto transmission and when you shift to reverse it really shifts hard ,it really jumps, when you put it in drive it shifts a little rough but nothing like it does in reverse anybody have any ideas ???

Messages Page 4 of 23 1 2 3 4 5 6 7 ... 23 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Pickups Ford Ranger Ford Ranger Transmission Questions