You are here: Forums Sedans Mitsubishi Diamante Mitsubishi Diamante Maintenance and Repair

Mitsubishi Diamante Maintenance and Repair

82 messages,  Last post on Nov 22, 2009 at 10:17 AM

You are in the Mitsubishi Diamante Forum. Your Hosts are pat & karens

What is this discussion about? Mitsubishi Diamante, Heating / Cooling, Sedan

Messages Page 9 of 9 1 ... 3 4 5 6 7 8 9 Prev Next Last

Go To Msg # Search This Discussion

#75 of 82 Crankshaft positioning sensor by doiturself Sep 27, 2009 (10:01 am)
Code came up on my 99 diamante. Took off the timing belt covers and noticed that it seems ( according to the length of the wires on the new one ) that it seems to go into the block about an inch and a half. maybe im not seeing it right, but have tried to replace it a couple of times and cant seem to figure it out. Maybe someone out there has done it before and can give me a hint. Please dont tell me the crank has to come out! lol Also looking for a helping hand on ditailed info on how to replace timing belt. doiturself
#76 of 82 Re: rear brake rotor [zasranec] by doiturself Oct 03, 2009 (12:07 pm)
Replying to: zasranec (Oct 17, 2007 5:38 pm) Ive got a 99 and when I went to change out the rear rotors they wouldnt budge. Maybe you will laugh when u hear this..... but on mine there were two extra holes in the area where the rotor slips on to the housing on oppisite sides of each other. Got a hair up my butt and treated it as though it was a steering wheel. I put two bolts that would fit into the threads and tightened them EQUALLY so it forcably pulled the rotor off the housing. I beat on the rotor for half an hour before trying this and it wouldnt budge. Dont know first hand if yours has the same extra holes in them but its worth a try instead of damaging something
#77 of 82 Re: 2000 Mitsubishi Diamante [diamoney] by doiturself Oct 03, 2009 (12:29 pm)
Replying to: diamoney (Jul 12, 2007 2:58 pm) dude that clicking is coming from the temp ajuster switch behind the ash tray under the dash. its got nothing to do with the fan
#78 of 82 Re: O2 Sensor [bill208] by tribe1 Oct 04, 2009 (1:27 pm)
Replying to: bill208 (Aug 27, 2008 2:10 pm) there are four o2 sensors... 2 in the front of the engine, one before and after the cat.
#79 of 82 Diamante 2002 [diamoney]Brake Pads by 1998lincoln Nov 01, 2009 (9:25 pm)
Replying to: diamoney (Sep 05, 2006 12:53 pm) Never buy lifetime pads,which is cheaper to replace ,the pads or the rotors!
#80 of 82 2003 Diamante LS windows fogging up by brianc702 Nov 15, 2009 (4:51 pm)
We have a 2003 Diamante LS and the windows have started fogging up. I've read a little about heater cores possibly being the culprit. Can someone give a definitive answer? We're trying to sell it (less than 40k miles) and I'd like to put this issue to bed. Thanks!
#81 of 82 1993 Diamante Wag - 'no start' by bowfan Nov 21, 2009 (8:41 pm)
I've got a '93 waggy that hasn't run for a couple years, originally stopped when the 4th/OD clutches went out. Just never made time to work on it, but I've decided it needs to go. V6-3.0L   This weekened I jump started it and don't think it's getting fuel. The engine does turn over. If I spray ether into plenum I can get it to fire momentarily, so I believe it's got spark.   Disconnected the fuel line which runs from fuel filter at the front fuel rail and cranked, but don't see any fuel coming out. I'd like to jumper the fuel pump and make sure the pump is good and not clogged up. I've got a 92-96 factory service manual but it seems to deal with the dohc engines, and I can't correlate the pics it shows with my engine compartment.   I believe there is supposed to be a connector in the engine compartment that you can hook +12v to test the pump, but can't seem to find it.   On a possibly related note, the fuel gauge is registering empty, even though I've added 10 gallons of fuel to it. I've been trying to read up and think that there is a relay that may power both the fuel pump and fuel gauge, but again, I'm not sure where this would be located.   Does anyone have any pointers on location of the FP relay, FP test connection or good advice?   Thanks!!! Replies to this message: Mr_Shiftright (Nov 22, 2009 10:17 am)
#82 of 82 Re: 1993 Diamante Wag - 'no start' [bowfan] by Mr_Shiftright HOST Nov 22, 2009 (10:17 am)
Replying to: bowfan (Nov 21, 2009 8:41 pm) not quite that easy. The multiport Fuel Injection Relay is located behind the glove box, and while it very well could be the cause of your problem, it requires a series of tests with a voltmeter, and a diagram of the various pins on the relay. One wrong move and you fry the whole thing.   I would suggest that you take out a subscription to www.alldatadiy.com for your car as it has all the diagrams and test procedures you need. I think it's $29 bucks for everything.   Or if you can find a used relay on eBay you can try to fix it that way.   There is indeed a "Fuel Pump Drive Terminal" to which you can apply battery voltage but the diagrams to not locate it, just show a picture of it (that's useless!).   I think a scan tool can easily power the pump as well. The pump appears to be in the fuel tank.   That's all I got for you at this time.

Messages Page 9 of 9 1 ... 3 4 5 6 7 8 9 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Sedans Mitsubishi Diamante Mitsubishi Diamante Maintenance and Repair