Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
Pickups Dodge Dakota Dodge Dakota Transmission Problems
693 messages, Last post on Nov 28, 2009 at 12:30 PM
You are in the Dodge Dakota Forum. Your Host is kcram
|
Replying to: fxallen (Dec 13, 2008 9:02 am) After reading dustyk post, he is correct. I had the dealer replace the shifter cable and when I went to pick up the truck, the mech could not get the ignition to unlock. After he removed the cable from the steering column, the ignition still would not unlock. His response to me when I asked what was next was, "...replace the steering column!" NO F'N WAY  was mine back to him! After he isolated the problem on the lot, I thanked him and took care of it at home. I increased the tension on the return spring by adding some additional material under the edge where it hooks over closer to the driver. I cleaned the area by blowing out the dust with on of those computer canned air cans and then used some molylube on the plastic parts. After all of this, the ignition has not given me any problems. With living in a very dusty, desert climate that constantly has winds blowing from 5-40 MPH, I can not complain. I did make sure I have the correct screwdriver in the glovebox, in case it should give me a hassle.  Let me know if I can be of any help. stealthb2
|
|
|
Thanks for the feedback guys. Seems to be no problem with the shifter cable per se ... works fine after the locking pawl is out of the way. Noticed that there is a recall on the 2001 and 2002's for roll aways due to this pawl NOT locking the shift lever in the Park position. HAS to be some common problem here and I'm thinking there is too much metal to metal contact with no "bearing, sliding type material" in between these two metal surfaces. The slider is quite long and seems to be just a pot metal slider against a pot metal surface on the column. Wonder what the replacement parts are for the fix for the recall?? Fred |
|
|
This Dakota has been in storage for several years. After warming up to operating temperature the tachometer reading goes bonkers showing extreme rpm and the transmission goes decides to go bonkers by shifting down to a lower gear with a maximum speed of 30 or so. Shifting the transmission to neutral and then back to drive allows the process to repeat. As a newbie to MoPar, I haven't the foggiest notion of what to look for -but- my gut says it is some sort of sensor related to speed or throttle. TIA macshasta service  macshasta.com
|
|
 i recently purchased a 99 dodge dakota single cab. while driving on the expressway, it would not shift out of third. rpms were roaring at 5 ( the red section) an i was only going about 45-50. while on a curvy stretch of road it did not handle curves well at all. the steering wheel would jerk if i turned it far left or right. and on the final stretch of residential streets, it would not shift out of second. i don't know much about the car and i would like to keep it, but i can't afford to spend anymore than $500 bucks. its in bad shape and i would like to get a plan together before i use the last drop of power left going to a mechanic. please advise
|
|
|
Replying to: macshasta (Dec 14, 2008 11:20 am) The Idle Speed Motor or Solenoid attaches to the Throttlebody Assembly. These get gummed up after a while and need to be cleaned. They will sometimes stick in the open position, which effectively raises the idle speed. You could also have a sticking/binding throttle cable or linkage. If the Throttle Pressure Pivot linkage is sticking, the return spring has rusted off, or the cable is binding, this can cause the throttle linkage to stick. A split or cracked vacuum hose will do the same thing. Because of this vehicle's age and mileage, I recommend checking all of the vacuum hoses for cracking and/or splitting. There are a number of sensors in the system that could contribute to this problem, the one most likely is the Coolant Temperature Sensor. This monitors the coolant temperature and feeds an input to the Powertrain Control Module (PCM). If the PCM thinks the coolant temperature is very low, it will send a signal to the Idle Speed Motor/Solenoid to increase the idle speed. Best regards, Dusty
|
|
|
Replying to: hadin (Dec 14, 2008 1:58 pm) I would first start with checking the transmission fluid level. On Chrysler built vehicles, the transmission fluid must be checked on a level surface with the engine at normal operating temperature and the gearshift in neutral. If the transmission fluid is low or too high, you will get slipping. If the transmission requires any fluid, use ATF+3 or ATF+4 fluid only. If the fluid level is okay, there are a number of things that could be at fault, such as a sticking or inoperative shift solenoid, bad electrical connections to the transmission, etc. You may need to have someone retrieve the fault codes from the computer before anticipating any diagnosis or repair. Most Auto Zone or Advantage Auto stores will check the computer for codes at no charge. Regards, Dusty
|
|
|
Replying to: dustyk (Dec 15, 2008 8:05 am) TIA macshasta service macshasta.com
|
|
|
Replying to: dustyk (Dec 15, 2008 8:16 am) Thanks Dusty
|
|
|
Replying to: macshasta (Dec 15, 2008 8:40 am) All the more reason to think you've got a vacuum leak. Good luck, Dusty
|
|
|
Replying to: hadin (Dec 15, 2008 10:51 am) Good luck, Dusty |
|
You are here:
Forums
Pickups Dodge Dakota Dodge Dakota Transmission Problems
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2010 Dodge Dakota
Browse by Board
Browse by Topic
Today's Chats
