Sign In Join 



Chevy Silverado and GMC Sierra 4x4 Questions

239 messages,  Last post on Dec 01, 2009 at 1:47 PM

You are in the Chevrolet Silverado & GMC Sierra Forum. Your Host is kcram

What is this discussion about? Chevrolet Silverado 1500, Chevrolet Silverado 2500, Chevrolet Silverado 3500, GMC Sierra 1500, GMC Sierra 2500, GMC Sierra 3500, Truck


Messages Page 6 of 25
1
...
3
4
5
6
7
8
9
...
25
Prev
Next
Last
Go To Msg #
Search This Discussion

#42 of 239
Boxed frames by jasper12
Dec 04, 2007 (4:51 pm)
Reply
Any thoughts on what will happen to the new boxed frames that cannot drain well or be readily flushed out, after several years on the heavily salted roads of the Northeast?
#43 of 239
95 Silverado 4X4 Wont Engage by conclutcha
Dec 04, 2007 (8:10 pm)
Reply
I Changed the Actuator but the 4X4 Wont Luck In. Someone told me that it has another switch but I cant find it Please Help.
#44 of 239
re: 4wd - & Re: Boxed frames [jasper12] by bruce48532
Dec 05, 2007 (6:15 am)
Reply

Replying to: jasper12 (Dec 04, 2007 4:51 pm)

I have a 1999 GMC 2500 just had the wheeling bearings replaced by the dealer at 90,000 apx miles. Cost $1000
 
Also sector shaft bearing in the transfer case replaced again by dealer $ 610. The sector shaft connects the transfer case motor.
 
Personally my opinion, with the thousands of dollars I've spent on 4wd repair and the additional cost to the truck purchase for auto 4wd.
 
GM should go back to manual shift, they cannot seem to get it right.
#45 of 239
Re: 95 Silverado 4X4 Wont Engage [conclutcha] by bruce48532
Dec 05, 2007 (6:19 am)
Reply

Replying to: conclutcha (Dec 04, 2007 8:10 pm)

my 1999 gmc 2500 has a transfer case motor that shifts the 4wd as well as the actuator on the front axle.
 
it could be the actuator motor on the transfer case that is your problem or it could be my most recent problem the sector shaft bearing in the transfer case.
#46 of 239
95 Silverado Wont Engage by conclutcha
Dec 05, 2007 (8:39 am)
Reply
Thank you For Your Info I Will Look At Some To Look For This Parts
#47 of 239
05 Z71 Auto 4X4 by jspillers
Dec 08, 2007 (7:14 pm)
Reply
Hello everyone,
I am new to the board, and have looked for a similar problem as mine, but can not find one.
I have a 2005 Z 71, with push button, 4WD, and the "auto" mode. I drive in 2wd, 30 minutes, 75mph, each way to work. Tranny works fine (with chevy's normal rough shifting) The other day I noticed the red light next to "neutral" was on instead of the amber light next to 2 Hi. The truck was running fine, and when I pushed the 2wd button, amber flashed for a few seconds, and went off. I pulled over, shut off the motor, restarted, and it apperantly reset. I thought life was good. Now I have noticed the red light on three more times, and it doesn't reset by simply restarting. It is very random when it is on, or off.
 
Any simmilar stories or advice?
#48 of 239
PUSH BUTTONS by jaron22
Dec 09, 2007 (6:28 pm)
Reply
I have a 4wd 1999 Gmc sierra 1500 and for some reason there are no push buttons in the dash. Does anyone know where i can buy any?
#49 of 239
thanks for the reply by gbillet
Dec 12, 2007 (12:18 am)
Reply
good thing i wasnt waiting on some help from you people never mind,i will figure it out on my own
#50 of 239
My 2002 Z71 4x4 service light is on ! by my2002z71
Dec 12, 2007 (7:17 pm)
Reply
My 2002 Z71 4x4 service light is on ! My 2002 Z71 4x4 service light is on !My 2002 Z71 4x4 service light is on !My 4x4 buttons do not work, and the 4x4 service light is on. I press the 4x4 buttons on the dash, and the 4x4 does not engage. Also my ABS light is on. It happened when the towed my vehicle. I am trying to work it out with the towing company.
#51 of 239
2004 GMC Sierra 2500 4x4 by boso56
Dec 15, 2007 (9:12 am)
Reply
I recently purchased an 04 GMC Sierra 2500 that was rolled over, after replacing the roof and other body damage (no damage to the front, rear or under carriage) I tried to engage the 4 wheel drive, the blinking lights tells me that it is engaged in 4 wheel drive. I hear it engaging in the transfer case, but the front axles do not engage. I purchased an actuator and installed it. It did not make any difference. On the highway it runs perfectly and quietly. Can you offer any suggestions on this matter?

Messages Page 6 of 25
1
...
3
4
5
6
7
8
9
...
25
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics

Today's Chats

Advertisement