Last post on Jan 30, 2011 at 12:45 AM
You are in the Ford Mustang
What is this discussion about?
Ford Mustang, Engine
#55 of 63 Re: 99 ford mustang [waterdr]
Mar 17, 2008 (8:18 am)
It's far from stock. It was built by proline racing,the same people who build engines for Tim Lynch. It has forged crank,rods and pistons,at about 8:1 compression, an AODE trans with brake.
#56 of 63 Re: 1969 engine swap to a 1993 5.0 [gmanfords]
Mar 23, 2008 (9:16 pm)
I have a convertible roof that looks to be in very good condition, however it is leaking a the bottom left corner of the rear window. Any ideas on how to stop it?
#57 of 63 Ford Mustang - Agent47 Retro Race Mirrors
Apr 26, 2008 (9:45 am)
Anyone swap out their stock Mirrors for the Agent47 Retro race Mirrors???
They are awesome and really improve the look.
#58 of 63 4.6liter power adders
May 09, 2008 (4:08 pm)
I got a 96 gt with BBK intake and BBK stainless exhaust. Was planning on changing the mass airflow sensor, putting in a bigger throttle body, and swapping out the exhaust manifolds for some shorty headers. Just curious if there are any cheaper ways of adding more power and if any of these ideas are a waste of money. Also take any suggestions on adding a chip.
#59 of 63 Re: 4.6liter power adders [gmedeiros83]
May 12, 2008 (9:41 pm)
Swapping the MAF is a complete waste of time. The MAF is designed to support about 400 hp, so unless you have made major modifications to the car, the MAF needs to be left alone unless it is damaged. One way to know for sure is to read the voltage from the MAF off a datalogger. If it is pegged at 5 volts, then it needs to be upgraded. Unless the car has a turbo or Supercharger, then a MAF upgrade is not needed. One exception would be if the fuel injectors are upgraded.
The stock headers on a Mustang are pretty efficient. Shorty headers are good for a solid ZERO hp unless the car has forced induction (turbo, supercharger). If it does, you might see a small gain. Long tubes are good for about 10 to 20 hp on a Mustang with forced induction.
You can upgrade the TB and upper plenum and get about 10 hp on your car.
However, the big opportunity that you are missing is upgrading the heads and cams. The 1996 to 1998 cars suffer from a crappy head design. The 1999 to 2004 cars made 40 more hp because of this. If I had a 1996 car I would go with ported heads and a nice set of cams and you get add about 100 hp, but expect to pay about $3000 especially with a chip and dyno tune.....more for installation.
#60 of 63 Help super charging an 01 GT
Aug 23, 2009 (3:48 pm)
I have an 01 GT 4.6 with 50,000 KM on it and would like to super charge it. Any tips or recomendations are appreciated.
#61 of 63 Add on electrical accessories
Mar 18, 2010 (8:27 am)
Im curious if anyone has an idea where would be a good point to connect an exciter wire connection or (ignition on) connection to trigger a relay to power accessories.
Although I am aware of how to find a location, I was curious if there is a standard point that ford identifies for this purpose. Thank you
#62 of 63 Re: Add on electrical accessories [saweber]
Mar 18, 2010 (9:08 am)
No standard. Just test the fuses until you find one. You can buy a special fuse insert that allows you to piggyback a power connection while still maintaining the fused protection.
#63 of 63 MY COLOR UPGRADE
Jan 30, 2011 (12:45 am)
Hello everyone, I have an 07 GT and want to know if I can upgrade my dash to include the "MY COLOR" option without a whole lot of headaches, and anyone have any idea of the cost?