You are here:
Forums
Pickups
Chevrolet Silverado & GMC Sierra
Chevy Silverado and GMC Sierra Transmission Problems

502 messages, Last post on Nov 08, 2009 at 8:49 AM
You are in the Chevrolet Silverado & GMC Sierra Forum. Your Host is kcram
|
|
|---|---|
|
i have an 88 silverado 1500 with the 700 r 4 tranny. i pulled my buddy out of the mud and the next day it didnt want to shift itself into 1st. so i would be leaving stoplights in 2nd gear. it would only go into first if i shifted it manualy on the collum. then when i would come to a stop the truck would die. it only wants to run in park or neutral. i can can get it to move if i rev it up to about 1700 rpm and drop it into gear and once im moving its fine. i was told it was the torqe converter. does anyone else have any ideas or have had a similiar problem? it is a rebuilt tranny with only 3000 miles on it. thanks Nick |
|
|
|
My automatic transmission is not shifting grears when it's on drive but if i shift from frist to second it will do it and then second to third it won't do anything it acts like its on neutral. Does anybody know whats wrong with it?can anybody help me!?!?!
|
|
|
|
| I posted back in May about my duramax, now just because yours may no be a duramax or an allison, DOESN'T mean you shouldnt read. My truck is STILL being worked on, and its OCTOBER! We found that there are many electronic components on the OUTSIDE of the tranny that can really screw things up if they get wet. On ours it was the "range switch" AKA "Park-Neutral Position Switch" AKA "Neutral-Back-up safety switch". Its a little electronic box on the outside of the tranny that relays info from your PRNDL display in the cab, to the transmission....If it gets wet, it will fry and your tranny won't work properly. It getting wet is caused by DIRECT water spray from a left turn onto this part (If the front and rear shields are NOT properly installed. We also found that, some of the wires going to different solenoids are shorted, that is what is being fixed now. Usually if you take your vehicle to a shop, they will scan it for codes....for FREE, just call around to find someone! its worth the drive and the time! | |
|
|
|
Replying to: chevygirl86 (Oct 06, 2009 9:17 am) |
|
|
|
|
Replying to: svga (Sep 19, 2009 10:15 am) |
|
|
|
|
Replying to: svga (Sep 19, 2009 10:15 am) |
|
|
|
|
Replying to: zante64 (Aug 03, 2007 2:49 pm) Being a GM guy most of my life, I bought a 1995 GMC Sierra W/T 4.3 V6 w/5 speed tranny in March '95. Tag says truck was built in Canada. With 6 miles on the odometer, I left the dealership when at the moment I first let off the clutch, the floor shifter popped out of first gear and slammed into the palm of my hand, nearly breaking my wrist. I simply thought this was my error of not having the shifter properly engaged, so I went along my happy way. About a month later while at a stop light, the same thing happened and again a month after that. I brought the truck back to the dealer to investigate the problem. They kept the truck 2 days before calling me to say they could not duplicate the symptom or find anything wrong. The problem continued once or twice monthly until it began occurring more often. The truck went back to the dealer 5 times thereafter with this problem. Each time they said they could not find or acknowledge any tranny problem. The truck's first year saw over 65k miles using 1st gear only at times when necessary (I had gotten used to it). By the third year, the problem had become so severe, it occurred almost every time while starting out from first, until at 278k miles, the tranny finally locked up one day requiring the truck to be towed to a transmission shop. The truck has always been serviced by the dealership during warranty. All fluids were replaced with the proper GM fluids, but they never would acknowledge this problem. I finally stopped using the dealership for service. Warranty had long run its course. At my expense, I had the tranny replaced with a used low mileage one as the shop said the original tranny had "melted" on the inside and although they had seen this condition before, it could not be rebuilt. One week and $2k later, the truck was serving me faithfully on the road again, only this time, for the first time in it's life, I was able to use 1st gear normally with no problems at all. Wow! At 427k miles, the second tranny became extremely difficult to shift into first and sometimes second gear. Another visit to the shop for a $1.6k shifter kit overhaul modification of some kind, it was almost like new again. They told me to "baby" it and it might get me by for two more years. Today, at 1/2 million miles on the odometer, this second $2k tranny with it's $1.6k shifter mod is now beginning to "melt down" on the inside (as they described it) like the first one did, although, it has never popped out of 1st gear like the original tranny did. Oh well, I can't complain! Will I go for a third tranny or not? After all, this truck has served me VERY well with an engine having never seen a wrench, burns/leaks no oil from oil change to oil change, performs reliably as a GM built work truck should and still gets me 23 MPG to this day! This leaves me to ponder one valid question: Why can't GM build transmissions to perform like that V6, 4.3 engine??? |
|
I have a 1993 Silverado. It shifts hard from 1st to 2nd then it won't shift into 3rd it is like it is in neutral. We have replaced the 2 soilinoids in it but it still isn't working right. We were told that it could be the speed sensor but haven't tried it yet. Does anyone know if it would be the speed sensor or what else it could be.
|
|
|
|
|
Replying to: katyc6 (Oct 24, 2009 10:49 am) I know of several people who own a Silverado with this same problem, but it seems the correct answer for each problem is not easy. Most all newer transmissions are now electronically controlled and there seems to be several issues that relate to this hard shifting from 1st to 2nd. What may be the answer for one "hard shifting" problem may not necessarily be the correct answer for another, so it seems. I'm not a transmission specialist, but it seems reasonable to conclude that heat will destroy an automatic transmission quicker than anything. Towing heavy loads produce lots of heat. Dirty fluid will produce excessive wear and tear, and ultimate failure of mechanical parts. It's just common sense. Keep the transmission cool as possible, keep the fluids clean as possible and it will likely last longer ... but things can go wrong also with the various mechanical and electronic components that must ALL be working properly in order to render proper operation of the transmission. I realize this may not be much help in your specific problem, but I thought I would mention this information since it is the same problem you are experiencing. There are many fantastic guys here that can shed more light on this subject, so a little patience and maybe we will both learn some interesting facts in the days ahead. Keep us posted on your findings and I'll do the same. Best ... |
|
| 2002 2500hd with durmax and allison transmission. when shift park to drive indecator light doesn't light up. will move and reverse is fine but no light or in neutral. fluid is clean and full when cold all works fine but when warm it acts up and service engine soon light stays on. any ideas? | |
You are here:
Forums
Pickups
Chevrolet Silverado & GMC Sierra
Chevy Silverado and GMC Sierra Transmission Problems
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2010 Chevrolet Silverado 1500
2004 Chevrolet Silverado 2500
2006 Chevrolet Silverado 3500
2010 GMC Sierra 1500
2004 GMC Sierra 2500
2006 GMC Sierra 3500



Browse by Board
Browse by Topic
Today's Chats