Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
SUVs Ford Bronco Ford Bronco Problems
231 messages, Last post on Nov 21, 2009 at 2:24 AM
You are in the Ford Bronco Forum. Your Hosts are steve_ & tidester
|
Replying to: miesk5 (Nov 11, 2007 6:30 am) |
|
| I have a 93 Bronco with 5.0. When I drive the truck for about 90 mile straight it starts cutting out and backfiring then it will just stop moving forward. The truck wont die but it cuts in and out. Let it cool down and you can drive it agian for an hour and a half or 90 miles or so. What is this problem. HELP. I cant find whats wrong. Be easy on me cause am not the best of mechanics.Thanks | |
|
Replying to: gator07 (Nov 15, 2007 3:46 pm) Do you have a check engine Light on? if so, post the Codes here for another reply. DIY Self Test & Connector Location & pics, Bronco & Ford BEST PROCESS WITH DIAGRAMS! Source: by Ryan M http://fordfuelinjection.com/?p=13 btw, A technician that is unfamiliar with the EEC Self-Test can mistakenly believe that continuous Memory codes are not present when they really are. He may run KOER Self-Test and get a pass code (111) and not realize that KOEO Self-Test must be run to receive any Continuous Memory codes. He may run KOEO Self-Test while counting MIL flashes and misinterpret the repeated hard fault pass code (111) to mean that Continuous Memory does not contain any codes. The engine temperature must be greater than 50°F (10°C) to pass the KOEO Self-Test and greater than 180°F (82°C) to pass the KOER Self-Test. To accomplish this, the engine should be at normal operating temperature One possibility is; Ford TFI Ignition Module; this is a good guess... but do the Self Test for Codes. Has that TFI Module been replaced Free under the recall? If you do not know, go to a Ford dealer and ask them to check using the VIN Code. or, DIY by registering at Ford and look to see what recalls are outstanding, plus; Owner Guides (Manuals), Bronco/Ford truck & other Ford vehicles, free, download Source: by Ford https://myford.fordvehicles.com/servlet/ContentServer?pagename=MyFord/Registrati- on/LogOnPage&BackToLogin=MyFord%2FHome%2FHomePage%26ord%3D15419550 Ford TFI Ignition Recall - the judge's order affected Fords manufactured between 1985 and 1995. http://www.summitlake.com/COMMENTARY/Ford_Ignitions.html?reload_coolmenus
|
|
|
Replying to: miesk5 (Nov 20, 2007 12:18 pm)
|
|
|
Replying to: gator07 (Nov 20, 2007 12:40 pm) OK, do that self-test anyway; some codes may be stored w/out lighting the CEL ABS; & do a self-test too here; The 4WABS connectors is red, & is under the hood right beside the engine test connector 4WABS System Component Locations, DTCs & Self Test & Connector Diagram; 93-96 Source: by Steve83 http://www.supermotors.net/vehicles/registry/media/255501_1 ABS Self test connector location; ABS (RABS II) Self Test , Diagnostic Connector Location, (title in article is wrong in article) Source: by autorepair.about.com http://autorepair.about.com/library/faqs/bl180d.htm GL! |
|
i have a 87 full size Ford Bronco w/ the EFI 5.0 & O/D A/T. a few months ago i replaced the entire fuel system, tank, both pumps, filter, lines, & ERG system (rust problem). a few weeks ago the acuator rod in the column broke & since i couldn't find a new column (can't buy an acuator rod seperate) i installed an aftermarket ignition switch in dash. 2 weeks after i did the switch, the Bronco stalled at a light, i was idling & now the fuel pumps won't run. I've changed the ECM computer, the fuel pump relay (which if i jump the hot terminal to the out going, the pumps run) and all related fuses with no luck. Does anyone have any suggestions as to what may be keeping the fuel pumps from running?
|
|
|
Replying to: tjewertz (Nov 25, 2007 2:42 pm)
|
|
|
Replying to: tjewertz (Nov 25, 2007 2:42 pm) Did you see any corrosion insde the FP Relay's socket? Fuel Pump Relay Socket Corrosion Info; spray it down with contact cleaner; They absolutely HATE moisture; also ck the EFI Power Relay (should be next to the FP Relay) for operation & corrosion. Next is the Inertia Fuel Cut-Off Switch (did you have a front end fender bender recently? see this by Bronco Rob & Steve 83; http://fullsizebronco.com/forum/showthread.php?t=38216 Fuel Pump Relay Operational Sequence; An inertia switch is used as a safety device in the fuel system. The inertia switch is located in the cab, generally under the dashboard on the right side. It is designed to open the fuel pump power circuit in the event of a collision. The switch is reset by pushing each of 2 buttons on the switch simultaneously (some models use switches with only one reset button). The inertia switch should not be reset until the fuel system has been inspected for damage or leaks. When the ignition switch is ON, it turns the EEC power relay ON. The EEC power relay provides power to the powertrain control module (PCM) and the control side of the fuel pump relay. Power for the fuel pump(s) is supplied through a fuse link or high current fuse attached to the starter solenoid (battery side). From the fuse link or high current fuse, current flows through the fuel pump relay and inertia switch to the fuel pump(s). The fuel pump relay is controlled by the PCM. When the ignition switch is turned ON, the fuel pump(s) will operate. If the ignition switch is not turned to the START position the PCM will shut the fuel pump(s) OFF after 1 second. The PCM will operate the fuel pump(s) operate the fuel pump(s) when the ignition switch is turn to START position to provide fuel while cranking. After the engine starts, the PCM will continue to operate the fuel pump(s) unless the engine stops, drops below 120 rpm or the inertia switch is tripped. GL! The pickup in the distributor can throw a code when it is intermittent or not working.. One of many reasons you should check your codes Have you done a code check? scan above for a DIY check that I have posted a few times here. |
|
|
Replying to: joeflew1 (Nov 26, 2007 12:38 am) The FP relay is in da IRCM (formerly called da CCRM) and it is Mounted forward of the airbox The CCRM is not usually serviceable. But if you want to take a shot at it see Joe's info in Link below Troubleshoot & Repair Your Malfunctioning Integrated Relay Control Module (IRCM) - by - J o e F r a z i e r NATO Member "Joe Cool http://www.turbotbird.com/techinfo/New_IRCM/IRCM.html CCRM = Constant Control Relay Module , IRCM = Integrated Relay Control Module;. This relay contols the fan, fuel pump and A/C clutch if i'm not mistaken. the fuel pump relay is tied into the IRCM on 94-95s; Since 1986, Ford has used, on several models, an Integrated Relay Control Module (IRCM) to operate the fuel pump, engine cooling fan and compressor clutch. During the early 1990’s, the name was changed to Constant Control Relay Module (CCRM). The module has a 24-pin connector . more Tech Info: http://www.dualcurve.com/5910-INST.pdf GL!!!!!!!!!!! |
|
Wherr is the realy for the ABS.It is not marked and there is lots of realys under the hood.thanks
|
|
You are here:
Forums
SUVs Ford Bronco Ford Bronco Problems
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
1996 Ford Bronco
Browse by Board
Browse by Topic
