Sign In Join 



Ford Bronco Problems

231 messages,  Last post on Nov 21, 2009 at 2:24 AM

You are in the Ford Bronco Forum. Your Hosts are steve_ & tidester

What is this discussion about? Ford Bronco


Messages Page 17 of 24
1
...
14
15
16
17
18
19
20
...
24
Prev
Next
Last
Go To Msg #
Search This Discussion

#155 of 231
running rough by dgiusti
Mar 05, 2008 (1:31 pm)
Reply
I have a 95 full size with a 351. It runs perfect for about 20-25 minutes then starts to run rough almost like a miss. I've changed plugs, wires, cap, rotor, o2 sensor, ignition module, fuel filter. Check engine light is not on. Prior to this starting I ran Lucas fuel injector cleaner through it and now am hearing bad things about that stuff in older vehicles. Has anyone experienced anything like this and if so what did you do??????
#156 of 231
Re: 1988 11 Bronco [dameen6] by dameen6
Mar 06, 2008 (8:17 am)
Reply

Replying to: dameen6 (Mar 04, 2008 3:06 pm)

does anyone respond to these or am i on the wrong
 forum. I am new at this. I need some help i can't afford to take it to the
shop maybe someone has some ideas that they can share or tell me
who i can talk to or maybe theirs a different forum i can go to. Yur help
would be greatly appreciated. THANK YOU EVERYONE
#158 of 231
95 ford bronco problem by nhernon
Mar 09, 2008 (3:41 pm)
Reply
I have a 95 ford bronco 5.8 L and the problem is i put it into low range and ever since then when i shift into reverse theres a big clunk and sometimes when i shift into drive theirs a big clunk also while im driving it will shift funny or sometimes wont even shift and i have to let off the gas would anybody maybe know the problem and if so maybe a solution to the problem? thanx
#159 of 231
Re: 95 ford bronco problem [nhernon] by dameen6
Mar 10, 2008 (10:12 am)
Reply

Replying to: nhernon (Mar 09, 2008 3:41 pm)

how are you PHERNON,well i have a 88 bronco 11, i had similar problems with mine,here's a couple of things you might want to check, driveshaft,universal joints,gears in the rear end, I don't know if you have automatic locking hubs check em also,check yur radius arm on both sides check the insulator and washer they usually are wore out and is rubbing on the crossmember that is some of the things that were done to mine. I HOPE IT HELPS YOU, good luck and let me know if any of them were bad, hopefully it isn't yur tranny, thats were i am stuck for now.
#160 of 231
Starting problem by dnolen
Mar 10, 2008 (11:29 am)
Reply
I have a '92 V8 5.0L Ford Bronco and I have a problem with the engine in the morning. The fuel pump needs to run for about 15 minutes before it has built up enough pressure to start.
The mechanics think it might be either the connection on the fuel pump. They're going to connect all three tubes seperately instead of together with one clasp.
If that doesn't help all they can do is replace the on board computer. My faith in mechanics is a little gone since I've spent more on repairs than on the initial amount I paid for the car.
 
Has anyone had the same problem or does anyone have any suggestions on where the problem might really lie?
 
  Any help is appreciated.
 
Thank you! Danielle
#161 of 231
Re: 95 ford bronco problem [nhernon] by bernie11
Mar 24, 2008 (7:43 am)
Reply

Replying to: nhernon (Mar 09, 2008 3:41 pm)

I had this problem before and all it was is a sensor in the engine. It only cost 85 dollars to replace. After that you won't get that jerking anymore. I thought it was the trans but it was only a sensor.
#162 of 231
maybe fuel system problems????? by cohide
Mar 25, 2008 (3:45 pm)
Reply
I have an 87 bronco that quit me today, it started twice but died each time after about 2 minutes or so, I'm thinking fuel filter but not real familiar with the fuel system yet, please help, my other truck is a diesel and diesel fuel prices are going through the roof, I have to get my "ol bronc" back on the road
#164 of 231
'93 full size trans "shudder"/vibration problem by droplever1
Apr 13, 2008 (12:27 pm)
Reply
I have a '93 full size Bronco 351 motor Dana(?) drive train w/140k problem started with a "thump" when shifting into reverse, hard ("jerky") shifting, then a vibration/"shudder"(like I'm riding over small rumble strips) when accelerating at 40-55mph. First time to shop they reccomended a service (fluid,filters,etc.) and a product called "shudderstop" for the torque converter. The "thump" went away and it was better for about a month then the shudder started again. Second trip to shop they tried a "shift-pak"(?) and solenoid(s). The thump and hard shifting are gone but I still have a vibration/"shudder" between 40 and 55mph when I accelerate. Any suggestions before I research replacing??? I hope to keep my Bronco indefinitely so I'm not opposed to replacement, but if it's not necessary I'de like to keep my money.
Thanks

Messages Page 17 of 24
1
...
14
15
16
17
18
19
20
...
24
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics

Today's Chats

Advertisement