Sign In Join 



Ford Bronco Problems

231 messages,  Last post on Nov 21, 2009 at 2:24 AM

You are in the Ford Bronco Forum. Your Hosts are steve_ & tidester

What is this discussion about? Ford Bronco


Messages Page 16 of 24
1
...
13
14
15
16
17
18
19
...
24
Prev
Next
Last
Go To Msg #
Search This Discussion

#142 of 231
83 ford bronco by grayhair2
Feb 07, 2008 (5:30 pm)
Reply
Hello, I have a problem, I just installed a rebuilt 302 engine, but it show to be getting hot according to the gauge in the dash, I have already replaced the temp sender unit, dash temp gauge, replace all hoses, and had the rad cleaned and vatted out. I had a 185 thermostat, and changed it to a 160, it helped. I dont really think it is over heating, because it has never has boiled over. I have checked it with a lazer temp gun, and it shows to be running at 160 degrees at the block, heads, and intake manifold. I have also check the wiring to make sure it is not grounding out anywhere. The temp needle will show below the half way mark, then after I turn on the A/C, the gauge start to go to the far right side , but still will be in the normal range. I have also ck the cooling fins to make sure the air flow is ok. The rad is a two row core rad. I could sure use some help. Thanks
#143 of 231
need help with a 87 broncoll that really bucks by storrs
Feb 22, 2008 (12:10 am)
Reply
I have a Bronco ll that starts bucking at about 2grand in any gear.It seems to run good till that point,after driving more it gets worse and worse so that it will buck no matter the rpms and then keep dying.I have changed the filters and can hear both pumps working.It seems to me like its electric problem.So I changed the coil,02 senser,throttle control senser.I am at a lose,can anyone help?PEASE.
 
  Russ
#144 of 231
Bronco's brake lights aren't working, but the turn signals are..? by meaganjoy90
Feb 25, 2008 (7:48 pm)
Reply
So I have a 1990 Ford Bronco II Eddie Bauer Edition. I haven't had many problems, until last week. There was a piece of metal in the middle of the road when my dad was driving so he pulled over to get it and turned on the emergency flashers. They flashed three times and then turned off. Since then, neither the brake lights or the emergency flashers are working, but the turn signals still work. He tried replacing the brake light switch and the turn signal switch, and neither of them worked. Just today, the flashers started working, but the brake lights still do not work.
So please help! My dad's too busy to get a lot of work done, and I'm a seventeen year old girl. What do I know about cars!
#145 of 231
Re: Transmission don't shift [hotpig] by storrs
Feb 25, 2008 (2:51 pm)
Reply

Replying to: hotpig (Jan 27, 2008 3:14 pm)

It sounds to me like the vacume mod. is not working or the vacume hose is off.
#146 of 231
89 5.0 idle problem by 89blackntan
Feb 28, 2008 (6:53 am)
Reply
i have an 89 ford bronco with a 5.0l. the idle stays at 2k rpms until i shift it into gear. i have replace the iac motor and checked all linkage, cleaned the throttle body, tuned the motor, checked the egr, im about to pull my hair out. the transmission is also slipping in overdrive and the tranny mechanic that i took it to said the aod tranny is controlled by the computer. can any one help.
#147 of 231
Re: Transmission don't shift [storrs] by 89blackntan
Feb 28, 2008 (6:54 am)
Reply

Replying to: storrs (Feb 25, 2008 2:51 pm)

how can i test it
#148 of 231
Help by 96xlt
Feb 29, 2008 (3:44 pm)
Reply
96 Ford Bronco 351, I am on my 3rd EGR valve in three months. I have reset the code several times to verify code but it comes back on about a week after I put in new EGR. Code is EGR flow insufficient. P0401 it is the only code that comes up.
#149 of 231
Re: 89 5.0 idle problem [89blackntan] by screwup
Mar 01, 2008 (4:30 am)
Reply

Replying to: 89blackntan (Feb 28, 2008 6:53 am)

mine did that,replaceed the thottle postion sencer
#150 of 231
88 FORD BRONCO (transmission problem) by dameen6
Mar 04, 2008 (2:17 pm)
Reply
well i had this beast for about 3 years, it was given to me as a present,now i did not know it was going to give me so many problems,i put in so much money i could of bought another truck it has new suspension,new fuel tank,sending unit,etc.I got it running last year in november 2007. I took it for a ride and it started leaking oil alot.,so i pulled the transmission off,it was a pita! fixed the leak bought new converter,flywheel,put it back together now it doesn't move forward or reverse,it has oil,what could it b,before i pull it of again this is my third time,different reasons the first two and it was fine and running everything looks fine,everything was connected correctly,maybe someone can help me with this problem or had this happen,i hope its something simple.
#151 of 231
Re: 1991 Bronco [qftball] by dameen6
Mar 04, 2008 (3:06 pm)
Reply

Replying to: qftball (Mar 22, 2006 10:45 pm)

how yu doing,i have and 88 bronco 4x4 i had that problem i replaced the transmission housing gasket and on that housing their a seal and pump seal that fixed my problem and on that pump theirs two seals on it they were also bad i hope it helps.

Messages Page 16 of 24
1
...
13
14
15
16
17
18
19
...
24
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics
Advertisement