Ask the Car People.SM


1983 Mazda B2000....HELP ME PLEASE!!!

16 messages,  Last post on Feb 29, 2008 at 7:31 PM

You are in the Speed Shop Tuning and Modification Forum.

What is this discussion about? Mazda B-Series Pickup, Exterior

Messages Page 2 of 2

#10 of 16 Looking for performance camshaft, 1986 B2000 by rjoertle

Jul 28, 2006 (5:54 pm)

I'm trying to locate a performance camshaft for a 1986 FE 2.0 SOHC in a B2000 pickup.

#11 of 16 Not Running by vahankin

Jun 14, 2007 (7:44 pm)

I recently purchased an 87' B2000. The guy started to work on it and removed the radiator, water pump, etc. to get to the timing belt. He is not interested in getting back into it so I picked it up for $150. All parts included except the radiator.
 
I am far from a mechanic...I plan to buy the book and attempt to put this thing back together. Does anyone have any suggestions or things to watch out for? I will be replacing the timing belt, water pump and radiator. These are all off of the vehicle already. All parts are there, I just need to figure out where they go. I'm a newby at working on vehicles so I want to make sure there aren't any items that with a little experience I would know about and not mess this thing up.
 
Thanks,

#12 of 16 Re: 1983 Mazda B2000....HELP ME PLEASE!!! [mazda1453] by the_bean

Feb 25, 2008 (1:46 pm)

Replying to: mazda1453 (Sep 29, 2005 10:40 pm)
i'm building an '86 b2000 right now and there's tons of places you could search...
 
jcwhittney.com
autopartswarehouse.com
ckresto.com
airbagit.com
godfathercustoms.com
sporttrucking.com
 
something you might be interested in though is that i heard a rumor that a kia spectra DOHC head will bolt right up to the block of the b2000 motor. thus making it easier to apply a turbo set-up! plus you get the added bonus of better gas milage, feul injetion, and more torque/hourse power. however i haven't been able to find what year kia the head should be pulled from. i'll keep looking and let you know what i find. e-mail me if you come up with any ideas or if you need tech help while your building at borderjumper21msn.com

#13 of 16 Re: 1983 Mazda B2000....HELP ME PLEASE!!! [mazda1453] by the_bean

Feb 25, 2008 (1:47 pm)

Replying to: mazda1453 (Sep 29, 2005 10:40 pm)
i'm building an '86 b2000 right now and there's tons of places you could search...
 
jcwhittney.com
autopartswarehouse.com
ckresto.com
airbagit.com
godfathercustoms.com
sporttrucking.com
 
something you might be interested in though is that i heard a rumor that a kia spectra DOHC head will bolt right up to the block of the b2000 motor. thus making it easier to apply a turbo set-up! plus you get the added bonus of better gas milage, feul injetion, and more torque/horse power. however i haven't been able to find what year kia the head should be pulled from. i'll keep looking and let you know what i find. e-mail me if you come up with any ideas or if you need tech help while your building at borderjumper21msn.com

#14 of 16 Re: Not Running [vahankin] by Mr_Shiftright HOST

Feb 29, 2008 (9:07 am)

Replying to: vahankin (Jun 14, 2007 7:44 pm)
These engines use VERY tricky carburetors that are expensive to replace and near impossible to rebuild. I'd be sure to get the engine running first, even without a radiator on it or pulley or alternator---just to be sure it runs right. If it runs badly you may want to bail out because a new carb will cost you a lot of money and you can buy these trucks very cheaply, all shiny and running great.
 
I'd encourage you to take this on as a learning project but don't get over excited and start spending money too fast. Take it a step at a time. You can run an engine without a radiator or accessories for a short time with no harm (a few minutes).
 
Don't buy untested junk parts and work from the core of the car (the engine) out toward the accessories. Don't be buying fancy wheels or a radiator before you even get the engine assembled.

#15 of 16 Re: Not Running [Mr_Shiftright] by the_bean

Feb 29, 2008 (11:07 am)

Replying to: Mr_Shiftright (Feb 29, 2008 9:07 am)
hey thanks for the advise and i took that into consideration and decided to scrap the whole "frankin-mazda engine" and just do an engine swap. i'm getting a toyota 5rz (3.4L 240hp fuel injected V-6) and 5speed manual tranny. i figured that would be a better route since i needed to get a drive shaft even if i kept the mazda engine.

#16 of 16 Re: Not Running [the_bean] by Mr_Shiftright HOST

Feb 29, 2008 (7:31 pm)

Replying to: the_bean (Feb 29, 2008 11:07 am)
That sounds like a worthwhile project. Is there a big difference in engine weight? I wonder. Also hopefully you won't have to set the engine too far forward. I'm presuming you are not going to work with power steering, so I bring this up. Also wider tires will also contribute to steering effort.

Messages Page 2 of 2

To POST a message, please Sign In.

Advertisement

Browse by Category

Browse by Vehicle
   View All Vehicles

Browse by Board
Browse by Topic
View All Topics

Edmunds Community

Advertisement