You are here: Forums Maintenance & Repair Mitsubishi 3000GT help

Mitsubishi 3000GT help

296 messages,  Last post on Nov 26, 2009 at 3:15 PM

You are in the Maintenance & Repair Forum. Your Host is mr_shiftright

What is this discussion about? Mitsubishi 3000GT

Messages Page 30 of 30 1 ... 24 25 26 27 28 29 30 Prev Next Last

Go To Msg # Search This Discussion

#288 of 296 Re: 1992 3000gt wot start help!!!! [crissy46526] by kiawah Nov 01, 2009 (5:03 am)
Replying to: crissy46526 (Oct 31, 2009 5:21 pm) is there a security system? Replies to this message: kenos (Nov 01, 2009 3:30 pm)
#289 of 296 Re: 1992 3000gt wot start help!!!! [kiawah] by kenos Nov 01, 2009 (3:30 pm)
Replying to: kiawah (Nov 01, 2009 5:03 am) You might need a new computer.
#290 of 296 What other year 5sp trans will work in a 96 3000gt? by riverrat57 Nov 19, 2009 (5:40 pm)
A friend of mine is trying to find a 5 speed manual trans to put back in his 96 3000GT, having a difficult time locating one in our area of NC, is there any other year(s) that will work?
#291 of 296 No pressure in Clutgh pedal by martini95 Nov 26, 2009 (11:33 am)
I have a 95 3000 and a few days ago i lost almost all pressure in the clutch pedal. I checked the master cylinder to check the fluid level and it was a little low so I refilled it. After that it was fine. but the next day I came back and I lost pressure again. I checked the fluid level again but it was full. Anyone got any ideas what might be the problem? Replies to this message: Mr_Shiftright (Nov 26, 2009 12:28 pm) 3kgtvr4 (Nov 26, 2009 12:39 pm) martini95 (Nov 26, 2009 2:16 pm)
#292 of 296 Re: No pressure in Clutgh pedal [martini95] by Mr_Shiftright HOST Nov 26, 2009 (12:28 pm)
Replying to: martini95 (Nov 26, 2009 11:33 am) If you lost some fluid, you have a leak, and probably are sucking in air. You might check for wetness at the clutch slave cylinder down below, or wetness in your carpeting under the dash where the clutch pedal linkage goes through the firewall.
#293 of 296 Re: No pressure in Clutgh pedal [martini95] by 3kgtvr4 Nov 26, 2009 (12:39 pm)
Replying to: martini95 (Nov 26, 2009 11:33 am) Yes check the slave. They fail more often than the master. Even if there is no wetness the seal inside can let fluid pass. Replacing it is not too expensive. Replies to this message: martini95 (Nov 26, 2009 2:16 pm)
#294 of 296 Re: No pressure in Clutgh pedal [3kgtvr4] by martini95 Nov 26, 2009 (2:16 pm)
Replying to: 3kgtvr4 (Nov 26, 2009 12:39 pm) do you know exactly where the slave is under
#295 of 296 lost pressure by firestoner Nov 26, 2009 (3:12 pm)
your slave cylinder is gone
#296 of 296 Where is your slave by firestoner Nov 26, 2009 (3:15 pm)
follow the line off the master cylinder & it'll take you right to it

Messages Page 30 of 30 1 ... 24 25 26 27 28 29 30 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Maintenance & Repair Mitsubishi 3000GT help