Sign In Join 



Subaru Crew MPG-Real World Numbers

87 messages,  Last post on Jun 24, 2008 at 12:29 PM

You are in the Subaru Crew Forum. Your Host is kcram

What is this discussion about? Subaru, Fuel Efficiency (MPG), Truck, Sedan, Wagon, SUV




Your Community Leaders are ateixeira and rsholland.


Messages Page 9 of 10
1
...
4
5
6
7
8
9
10
Prev
Next
Last
Go To Msg #
Search This Discussion

#74 of 87
Re: 97 legacy outback 2.5 [stevecebu] by p0926
Jun 22, 2007 (11:34 am)
Reply

Replying to: stevecebu (Jun 20, 2007 10:36 am)

Huh? What's not relevant? Dliboiron wasn't asking how to calculate his mileage, he was asking how how many liters the tank holds (60L sounds right).
 
-Frank
#75 of 87
Re: Subaru Crew: MPG-Real World Numbers [KarenS] by mike205
Jul 10, 2007 (4:30 pm)
Reply

Replying to: KarenS (May 16, 2005 6:33 am)

06 Legacy Wagon 2.5iSE with Automatic Transmission
- rated 23 - 30mpg EPA.
 
Actual 100% Highway 26 - 29 mpg.
Actual 90% City Short-Haul point to point - 16 - 18mpg.
#76 of 87
Re: Subaru Crew: MPG-Real World Numbers [mike205] by paisan
Jul 14, 2007 (7:34 pm)
Reply

Replying to: mike205 (Jul 10, 2007 4:30 pm)

05 LGT Wagon 5MT
30k miles
 
So far only did a highway trip 75-80mph, 28.x mpg
 
I'll post back when I do some city driving.
 
-mike
#77 of 87
Re: Subaru Crew: MPG-Real World Numbers [paisan] by ateixeira
Jul 16, 2007 (7:26 am)
Reply

Replying to: paisan (Jul 14, 2007 7:34 pm)

Sweet mike, you sure you were going "only" 80?
#78 of 87
Re: Subaru Crew: MPG-Real World Numbers [ateixeira] by paisan
Jul 16, 2007 (1:13 pm)
Reply

Replying to: ateixeira (Jul 16, 2007 7:26 am)

yup cruise control has saved me from many tickets! I set it on 75 these days and leave it there.
 
-mike
#79 of 87
Increase of ~2.5 mpg by amsbear
Oct 15, 2007 (7:22 am)
Reply
Since replacing my Knock Sensor, I have seen a nice increase in MPG . It was throwing an intermittent CEL (P0325) that specified a Knock Sensor Circuit Malfunction and was able to replace it myself (with a few hiccups) and since then been rewarded with the following jump in MPG over the past two tankfulls.
 
Most recent MPG results.
25.925
25.684
22.684
23.170
24.430
22.689
22.814
23.060
 
Now those "hiccups" were due to me leaning into the engine bay a bit too hard while doing the sensor replacement .
 
#1 - I unseated the cruise control cable/linkage a bit which caused a P0507 Idle Control System RPM Higher Than Expected CEL. I started hunting down IAC issues until I noticed the problem and simply resnapped the cable back.
 
#2 - Cracked a vacuum line that operates the EGR, which led to it throwing the P0400 EGR Flow Malfunction. Fixed that with a new section of appropriated tubing.
 
Now I can take it in for inspection with my fingers crossed.
 
Alan
98 OBW Ltd - 139,500 miles
#80 of 87
Knock Sensor by masteryoda
Oct 18, 2007 (7:47 pm)
Reply
Hi Alan. I got a CEL light myself for the Knock Sensor on my 98 GT. Do you have instructions on how to change it?
#81 of 87
Re: Knock Sensor [masteryoda] by amsbear
Oct 19, 2007 (9:06 am)
Reply

Replying to: masteryoda (Oct 18, 2007 7:47 pm)

Recommended tools:
  Flashlight
  Socket wrench
  8" socket extension
  12mm socket
  Magnetic pickup tool
 
Finding the sensor was the first issue.
 
[copied from a Nabisco post]
The knock sensor is located on top of the block, above the #4 cylinder. It should be on the drivers side, left of the throttle body near the cable linkage if you are standing in front of the engine. There may be a EGR solenoid in the way, so you need to peer pass that to see it. It should be a black round thing with a 12mm bolt through the middle, connected by one wire, but with a white 2-pin connector.
 
Getting to it with hands and tools is the 2nd issue
From the drivers side -
With the socket on the extension, I seated it on the bolt, attached the wrench and backed it out. I had the magnetic pickup handy to get the bolt fully out. Put this aside as you will likely need it during the replacement, my part from the dealer did not come with a new bolt.
 
From the passenger side -
Pull the sensor out into the more open area on the left side of the throttle body. I pulled it through using where it connects to the harness.
There is not enough room on the right side to get both hands in to release the connector from the harness.
Unclip it from the harness and attach the new one onto the harness and thread the sensor back under the throttle body.
 
Back on the drivers side -
Again use the magnet tool to pull it into the generally area where it has to be remounted.
Put the bolt back through the center of the sensor and carefully guide it back down towards the engine block.
With just the extension and socket, attach to the bolt and "feel it" back into the bolt hole.
Turn it counter clockwise a bit just to be sure of alignment and that you will catch the threads correctly.
Attach the wrench and tighten it down, but not too tight. There are warnings that you can damage the sensor if you really overtighten it.
 
"Plug n Play" right?!?!
 
Clear your code(s) and start her up.
 
Good Luck!
 
Alan
98 OBW Ltd
#82 of 87
Re: Knock Sensor [masteryoda] by amsbear
Oct 19, 2007 (9:26 am)
Reply

Replying to: masteryoda (Oct 18, 2007 7:47 pm)

BTW, my dealer charged me $107 + tax. If you are not in a hurry, I am sure you can get a better price online.
 
I used a Subaru Bucks coupon so it was only $15 out of pocket.
 
Alan
98 OBW Ltd
#83 of 87
Re: Knock Sensor [amsbear] by dliboiron
Oct 21, 2007 (8:54 pm)
Reply

Replying to: amsbear (Oct 19, 2007 9:26 am)

Subaru bucks, how do you get those? Are they available in Canada?

Messages Page 9 of 10
1
...
4
5
6
7
8
9
10
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics

Today's Chats

Advertisement