This forum is for anyone interested in the 300ZX, all years and variations.
- #233 of 317
-
rubber molding
by jfkgunner
-
Jan 23, 2008 (11:09 am)
-
|
|
Have a 86 300ZX, back window and t-tops need the rubber molding replaced. Does anybody know where to get some? Nissan does not make anymore and no one on the internet car parts shops have it.
|
- #234 of 317
-
fuse panel diagram
by bucrucox08
-
Jan 26, 2008 (9:54 am)
-
|
|
I don't have the cover for fuse box on the kicker pannel for my 1990 300zx 2+2 non-turbo. I was wondering if anyone had theirs or knew off hand which fuse ran for the drivers window. Thanks (ps anyone need any parts lemme know)
|
- #235 of 317
-
Re: rubber molding [jfkgunner]
by z32chic
-
Jan 28, 2008 (1:52 pm)
-
|
|
Replying to: jfkgunner (Jan 23, 2008 11:09 am)
ebay ebay ebay
|
- #236 of 317
-
Re: cuts out at 2500 rpm [84_300zx]
by bpuz31
-
Jan 28, 2008 (5:27 pm)
-
|
|
Replying to: 84_300zx (Feb 13, 2007 9:53 am)
it could be your TPS there is a plastic piece with a metal strip on it that is glued to the rotating part of the sensor.when you rev it up the throttle opens and the plastic piece stays still and continues to make continuity when it shouldnt be so the computer thinks that the car is only at idle so the engine doesnt get enough fuel.mine did the same thing.i tied some floss arond it.its been wokin since, i never got a new one.
|
- #237 of 317
-
Re: Starting Problem 1993 300ZX (non turbo) [corvette8]
by ducky6
-
Feb 22, 2008 (3:40 pm)
-
|
|
Replying to: corvette8 (Apr 07, 2006 6:33 am)
i am have this kind of problem with my 96 300 zx when i get to a stop sign or light it shuts off but will start right back up most of the time.
i stuck and dont know what to do!!
|
- #238 of 317
-
Re: Starting Problem 1993 300ZX (non turbo) [ducky6]
by bpuz31
-
Feb 23, 2008 (8:12 am)
-
|
|
Replying to: ducky6 (Feb 22, 2008 3:40 pm)
is it automatic?does it do it at EVERY stop you come to?only hard stops?if it is auto you might be able to raise the idle..i had an 84 auto...it did what yours does
|
- #239 of 317
-
Re: Starting Problem 1993 300ZX (non turbo) [ducky6]
by bucrucox08
-
Feb 23, 2008 (2:23 pm)
-
|
|
Replying to: ducky6 (Feb 22, 2008 3:40 pm)
mine was doing the same thing....i had popped a tiny vac line off..the one by the 5th cylinder...it would die at a stop sign ...would be fine when i first ran it...and fine driving around...i never even noticed it was off...no check engine light or anything...worth at least checking. good luck
|
- #240 of 317
-
Re: Starting Problem 1993 300ZX (non turbo) [bucrucox08]
by jim300zx
-
Feb 25, 2008 (9:15 am)
-
|
|
Replying to: bucrucox08 (Feb 23, 2008 2:23 pm)
I am having a different starting problem with my 91 turbo. Most times it starts fine, but now and then I turn the key and the dash lights come on but nothing else happens. Usually, if I turn the key a few times it starts fine. I have replaced the starter and adjusted the clutch switch, but it still happens now and then. Any ideas? (Of course, it starts fine when AAA shows up or when I take it to a mechanic.)
Thanks
|
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
Coupes & Convertibles 
