You are here: Forums Hatchbacks Mazda3 Mazda3 Maintenance & Repair

Mazda3 Maintenance & Repair

4531 messages,  Last post on Oct 22, 2009 at 5:40 PM

You are in the Mazda3 Forum. Your Host is pf_flyer

What is this discussion about? Mazda MAZDA3, Hatchback, Sedan

Messages Page 426 of 454 1 ... 423 424 425 426 427 428 429 ... 454 Prev Next Last

Go To Msg # Search This Discussion

#4244 of 4531 Re: P0715 Input/Turbine Speed Sensor Circuit Malfunction, any ideas? [mazda by mazdazoom Mar 04, 2008 (8:30 pm)
Replying to: mazdazoom (Feb 19, 2008 6:52 am) I realize I am responding to my own post, but I thought someone might find this useful. In regards to the 0715 error message Mazda agreed with me that it was the "speed sensor" located near the bottom of the tranny near the firewall, or the pulse generator located at the top of the tranny right under the battery box. Well I replaced the speed sensor myself and I still had the problem. So I went out and picked up a pulse generator (another sensor similar to the speed sensor) and replaced it myself. BINGO, that was the culprit, and the tranny is shifting better than it ever has. So just an update, if you get the P0715 error, it is either the speed sensor or the pulse generator sensor, I just replaced both sensors for good measure, $160 total. Save yourself the $200 in labor and swap it out, took me about an hour with test driving. Replies to this message: nocents (Apr 10, 2008 6:40 am) mazdazoom (Apr 10, 2008 7:18 am)
#4245 of 4531 Re: Speed3 Fuel Injector noise [roadburner] by tarheelschik Mar 05, 2008 (6:42 pm)
Replying to: roadburner (Mar 02, 2008 5:36 pm) What all did the recall entail about the shutter valve, and how do I go about finding out about having mine checked out? My CEL has been on for a few months now, and when I had the code read, I believe it said something about the shutter valve, and then once about the upper intake runner closed or something to that effect. Replies to this message: roadburner (Mar 06, 2008 10:47 am) tarheelschik (Mar 06, 2008 6:12 pm)
#4246 of 4531 Re: Speed3 Fuel Injector noise [tarheelschik] by roadburner Mar 06, 2008 (10:47 am)
Replying to: tarheelschik (Mar 05, 2008 6:42 pm) What all did the recall entail about the shutter valve, and how do I go about finding out about having mine checked out?   Check with you dealer and see if your VIN falls within the range affected by the recall. In most cases the valve is replaced and the PCM(engine computer) is reflashed. Replies to this message: tarheelschik (Mar 06, 2008 6:12 pm)
#4247 of 4531 Speed3 Turbo Failure by comet2003 Mar 06, 2008 (4:09 pm)
Hello all MazdaSpeed3 and Mazda3 owners.   I own a 2007 Speed3 with only 6500 miles which began belching blue smoke. A trip to the dealer resulted in the dealer being instructed by Mazda Tech to hold my car and order a new Turbo. The replacment Turbo is on national backorder at this time. I've since learned that my car is among a number of Speed3s which are requiring replacment of the Turbo.   I have not seen any postings of this problem here, so unfortunately I guess I'm the first to report this here at Edmunds. Replies to this message: Mr_Shiftright (Mar 06, 2008 5:10 pm) roadburner (Mar 06, 2008 7:58 pm) comet2003 (Mar 18, 2008 4:51 pm) roadburner (Mar 18, 2008 5:28 pm)
#4248 of 4531 Re: Speed3 Turbo Failure [comet2003] by Mr_Shiftright HOST Mar 06, 2008 (5:10 pm)
Replying to: comet2003 (Mar 06, 2008 4:09 pm) You could drive the car this way I think. Sounds like the bearings are loose in the turbine or the compressor side. This is often caused by poor lubrication or very dirty oil--but rarely at this low mileage.
#4250 of 4531 steering, suspension, alignment... by mazdrvr Mar 06, 2008 (5:41 pm)
Hi, i need your guys help again. This tire blowout incident is becoming a costly headache!!! After a week i got my car back & was recommended to do a alignment. The impact of whatever the tire struck (or vice versa) was so hard they said there was a hole in the tire (explains the bent rim & bumper damage). The front where it happens makes a pop, "boing" noise when the wheel is turned lock to lock. Also on that side, when i drive & go over certain bumps, you hear & feel a knock. I had a alignment done today but still noticed some things and wondered if someone could tell me if i might be so i can have it checked & hopefully fixed...   1. steering wheel still not centered, turned slightly to right & hear a "rubbing sound when i turn it. 2. when i drive & go over certain bumps, you hear & feel a knock. 3. makes a pop, "boing" noise when the wheel is turned lock to lock (something in strut, suspension?). Much appreciation & Thanks in advance!! Replies to this message: roadburner (Mar 06, 2008 7:49 pm)
#4251 of 4531 Re: Speed3 Fuel Injector noise [roadburner] by tarheelschik Mar 06, 2008 (6:12 pm)
Replying to: roadburner (Mar 06, 2008 10:47 am) Ok. Thanks for the info. I called the Mazda dealer that is around here, and they ran my VIN, and they said there are no current recalls for my car, and that the only one they have on file that was for my car was back in 2004, and that was for an air bag sensor that they fixed already. So everything checks out I guess. I just need to find out what is going on with the stinkin CEL now!
#4252 of 4531 Re: steering, suspension, alignment... [mazdrvr] by roadburner Mar 06, 2008 (7:49 pm)
Replying to: mazdrvr (Mar 06, 2008 5:41 pm) I had a alignment done today but still noticed some things and wondered if someone could tell me if i might be so i can have it checked & hopefully fixed...   I'd suspect ball joints, tie rod ends, control arm bushings, bent strut(s), or strut bearings- in that order.
#4253 of 4531 Re: Speed3 Turbo Failure [comet2003] by roadburner Mar 06, 2008 (7:58 pm)
Replying to: comet2003 (Mar 06, 2008 4:09 pm) I have not seen any postings of this problem here, so unfortunately I guess I'm the first to report this here at Edmunds.   As you probably know, the problem has been discussed on some of the more technical oriented Mazdaspeed boards since mid December. It's appears to occur with greater frequency on modded cars which have had one or both cats removed. Stock MS3s have been affected as well, but less frequently. I figure that if mine is bad it will likely fail before the powertrain warranty runs out... Replies to this message: comet2003 (Mar 18, 2008 4:51 pm) roadburner (Mar 18, 2008 5:28 pm)

Messages Page 426 of 454 1 ... 423 424 425 426 427 428 429 ... 454 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Hatchbacks Mazda3 Mazda3 Maintenance & Repair