Got a Quick, Technical Question?

4960 messages, Last post on Nov 25, 2009 at 8:23 AM

You are in the Maintenance & Repair Forum. Your Host is mr_shiftright

What is this discussion about? Brakes, Electrical, Engine, Exhaust

A Place to Post A Question That Doesn't Need a Discussion--Only One Quick Answer!

Outline

Messages Page 467 of 497: 1; ...; 464; 465; 466; 467; 468; 469; 470; ...; 497; Prev; Next; Last

#4654 of 4960 Re: I think I may have been ripped off: Hydraulic Engine Mount [pam4water] by euphonium Nov 10, 2008 (10:53 am)
Replying to: pam4water (Nov 08, 2008 1:18 am) You can be safe with a stranger when your hand is on the Glock. Why go around unarmed, the crooks aren't?
#4655 of 4960 99 mazda millenia s by natekelly Nov 16, 2008 (7:06 am)
when driving my car and hitting 2500 RPM it starts stalling and jumping like it has a real bad miss. does anyone have any opinions on this? thx. Replies to this message: Mr_Shiftright (Nov 16, 2008 7:46 am) kiawah (Nov 16, 2008 2:02 pm) Mr_Shiftright (Nov 17, 2008 8:50 am)
#4656 of 4960 Re: 99 mazda millenia s [natekelly] by Mr_Shiftright HOST Nov 16, 2008 (7:46 am)
Replying to: natekelly (Nov 16, 2008 7:06 am) Sounds like an ignition system issue. Have we had a tune up lately?
#4657 of 4960 Re: 99 mazda millenia s [natekelly] by kiawah Nov 16, 2008 (2:02 pm)
Replying to: natekelly (Nov 16, 2008 7:06 am) or fuel delivery issues. Doesn't use much fuel when idling, but as you are revving it up it would need more fuel delivery from the fuel pump/filter. But your problem could be many things, you should take it somewhere to have them diagnose it properly. Replies to this message: Mr_Shiftright (Nov 17, 2008 8:50 am)
#4658 of 4960 Re: 99 mazda millenia s [kiawah] by Mr_Shiftright HOST Nov 17, 2008 (8:50 am)
Replying to: kiawah (Nov 16, 2008 2:02 pm) Could be, but I'm always suspicious of ignition when the problems start at a specific rpm....seems to me if you had fuel pressure that bad you'd never get up to 2,500 rpm.
#4659 of 4960 Timing chains on Toyotas by inkie Nov 17, 2008 (10:12 pm)
It would be appreciated if anyone can let me know what Toyota models {if any] have steel timing chains? Also, do any engines they manufacture are non-interference? Thanks. Replies to this message: suvshopper4 (Nov 18, 2008 6:41 pm)
#4660 of 4960 Re: Timing chains on Toyotas [inkie] by suvshopper4 Nov 18, 2008 (6:41 pm)
Replying to: inkie (Nov 17, 2008 10:12 pm) I know the 2.0L 4-cyl in the 2001 and forward RAV4 has a timing chain, not a belt. I have read that Toyota engines are non-interference (unlike Honda). -ss4
#4661 of 4960 Toyota Timing Chains [suvshopper4] by inkie Nov 18, 2008 (10:15 pm)
Thank You, I have not had too much luck with these questions at the dealers in the Lehigh Valley.Whenever I get there the service manager is not in and the underlings were probably told not to discuss anything and refer me to the service manager. Pretty fancy not like Honda and GM. Now that I have some engine models it may be easier to get specs.
#4662 of 4960 code 1810 by shooter7 Nov 20, 2008 (11:46 pm)
I have a 2000 saturn l series 300 v6 with transaxel. it wont go forward or reverse. code checker says 1810... ATF pressure manual valve position switch malfunction. can I fix this from under the car or does the tranny have to be taken apart? thanks Replies to this message: Mr_Shiftright (Nov 23, 2008 10:06 am) shooter7 (Nov 23, 2008 1:21 pm)
#4663 of 4960 Lexus ES300, 1994 front rotors 270K by edouble1 Nov 22, 2008 (6:28 pm)
Trying to replace the front rotors. Seems pretty straight forward: remove the wheel, remove the break calliper, remove the calliper bracket, slide the rotor off. I can't get the rotor off. I don't think they were ever replaced before, and there is 270K miles on it. What are the chances it's rusted on? Will PB blaster help in the process? How hard can I bang on the back of the rotor with a hammer, if I use a Hammer/block of wood, or a rubber mallet? Thanks for your help. Replies to this message: bolivar (Nov 23, 2008 1:45 am)