Sign In Join 

You are here: [F] Forums / SUVs / Mitsubishi Endeavor / Mitsubishi Endeavor Maintenance and Repair



Mitsubishi Endeavor Maintenance and Repair

408 messages,  Last post on Nov 25, 2009 at 7:49 PM

You are in the Mitsubishi Endeavor Forum. Your Hosts are steve_ & tidester

What is this discussion about? Mitsubishi Endeavor, SUV


Messages Page 33 of 42
1
...
30
31
32
33
34
35
36
...
42
Prev
Next
Last
Go To Msg #
Search This Discussion

#312 of 408
One of my red rear lights is brighter than the other by jp007
Feb 21, 2008 (11:28 am)
Reply
I noticed after driving my wife who was driving the SUV that one of the rear light is brighter than the other. We are not talking about just a little brighter but a lot. It is as bright as when she hit the break. Therefore if she hits the break, the other light will become as bright as the first one. Somehow for that one light, it is stuck at the brake light intensity.
 
Has anyone experience this? Is this due to an incompatible bulb?
#313 of 408
Re: Trailer Wiring ??? [kidder] by cfrench
Feb 27, 2008 (10:19 am)
Reply

Replying to: kidder (Feb 10, 2008 8:45 am)

Do You happen to have the part number to this electrical plug ? I have a 2004 mitsubishi and have encountered the same problem. I too hate the splicing wires.
 
Clayton
#314 of 408
Glove Box Door by cfrench
Feb 28, 2008 (7:17 am)
Reply
I have a 2004 Endeavor XLS and for the life of me I cannotkeep the glove box door from squeeking. Open the glove box door and it quits, big deal. I have tried stick on pads in inconspicuous places, but no help. Anybody had this problem?
#315 of 408
Re: Glove Box Door [cfrench] by mikevegas06
Mar 01, 2008 (4:41 am)
Reply

Replying to: cfrench (Feb 28, 2008 7:17 am)

I don't have an Endeavor but I have had similar problems on other vehicles. The sticky pads was a good first move though. With the glove box open, there might be some screws visible on the latch/locking mechanism that resides in the glove box door. Try adjusting those. Also, try applying a little bit of lubricant to the plastic hinges. One last thing, is the glove box still noisy when you've completely removed all of its contents?
#316 of 408
Re: Glove Box Door [mikevegas06] by cfrench
Mar 05, 2008 (10:37 am)
Reply

Replying to: mikevegas06 (Mar 01, 2008 4:41 am)

Thanks. I tried all of the mentioned in your letter. Finally I got the glovebox out altogether. There is no adjustment on the "Catch", therefore I just bent it slightly and so far, it seems to cure the problem. It just stuck out a bit too far. Again, thanks for your response.
#317 of 408
Re: Exposed radiator [cweiss] by bigdadi118
Mar 12, 2008 (7:13 pm)
Reply

Replying to: cweiss (Mar 05, 2007 5:12 pm)

You should check out the thread of "Grille Inserts" in Honda Odyssey site here. There are many D-I-Y options, cost from $4 to $200's ... I protected my Bumper opening by $4 Home Depot gutter screen + plastic cable ties. The Honda condensor replacement costs $750.00.
 
A guy posted photos re how to do it there, take off the front then assemble them back. I spent about 45 mins to complete the job
#318 of 408
Re: Glove Box Door [cfrench] by mikevegas06
Mar 13, 2008 (2:30 am)
Reply

Replying to: cfrench (Mar 05, 2008 10:37 am)

Hey sorry for the delay in my response. Cool. Glad that you fixed it. I never thought about removing the glovebox entirely for a better look at it. Thanks for the tip.
#319 of 408
Re: Glove Box Door [cfrench] by ccarl1
Mar 24, 2008 (4:48 pm)
Reply

Replying to: cfrench (Mar 05, 2008 10:37 am)

Hi,
I'm not sure if this is a new thread, but you said you removed the glove box, so I'll ask you first. I'm trying to get the glove box out to replace the cabin filter. I removed the four screws in the diagram of the glove box, but the picture shows 'hook crochets' (three on rt, two on left) which are what must be holding the plastic in place, because I can't budge it. How did you remove the glove box?
#320 of 408
removing glove box for cabin filter installation by ccarl1
Mar 24, 2008 (5:07 pm)
Reply
I have a 2004 Endeavor and am trying to replace the cabin air filter. The schematic I got shows dropping the glove box door to remove the four screws, which I've been able to do. But that's where I'm stuck. The diagram also shows 'hook crochets' which must be what's holding the plastice in place (2 on left, 3 on rt), but I can't figure out how to release them. I don't want to damage anything. Anyone done this and can tell me how to proceed?
#321 of 408
Re: Glove Box Door [ccarl1] by cfrench
Mar 25, 2008 (6:02 am)
Reply

Replying to: ccarl1 (Mar 24, 2008 4:48 pm)

As you already did, you unhook the tension cord, take out the (4) screws, 2 on top, two on bottom. Now you have to get serious with it.. Put Your fingers under the liner at bottom right and pull (just the bottom right, don't try to pull the whole unit strait out. It wont break, it will eventually flex and the hook crochets will disengage. From there you can work the left side out from under where the vent comes out. ( I just came in from doing it again to see if I remembered it right) Good Luck) In this forum You can get this filter from Mitsubishi Parts for $23.00, every other place I looked, they want twice as much.
 
Clayton

Messages Page 33 of 42
1
...
30
31
32
33
34
35
36
...
42
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

You are here: [F] Forums / SUVs / Mitsubishi Endeavor / Mitsubishi Endeavor Maintenance and Repair

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Learn More

2010 Mitsubishi Endeavor

2008 Mitsubishi Endeavor SE SUV Shown

More Pictures

DoMore

Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics

Today's Chats

Advertisement