You are here: Forums Pickups Mazda B-Series Mazda B Series

Mazda B Series

747 messages,  Last post on Oct 23, 2009 at 10:23 PM

You are in the Mazda B-Series Forum. Your Host is kcram

What is this discussion about? Mazda B-Series Pickup, Mazda B-Series Truck, Truck

Messages Page 72 of 76 1 ... 69 70 71 72 73 74 75 76 Prev Next Last

Go To Msg # Search This Discussion

#702 of 747 Re: 1988 B2200 - NEEDS CARBURATOR! [minty] by minty Aug 18, 2006 (9:56 am)
Replying to: minty (Aug 17, 2006 7:38 pm) Nevermind. Figures as soon as I post this message, the next day, my truck has been repaired. Thanks anyways!
#703 of 747 Re: Mazda B Series [billmoore22] by abgager Aug 28, 2006 (5:05 am)
Replying to: billmoore22 (Jul 11, 2005 5:38 pm) I have just experienced a similar high revving problem for the first time. Towards the end of a 3.5 hour drive the rpms on my 2000 b3000 starting shooting up (more than 4000rpms) whenever I pushed in the clutch. It stays high for a few seconds (5-10) then drops down to a normal idle level. At first, putting the car in neutral would make the revs drop down to normal (1k rps) but then the revs started shooting up even when in neutral with the clutch out. I pulled over, turned the car off and the problem went away when I started driving again for about 1/2 hour but then the problem came back.   Any ideas? Replies to this message: abgager (Aug 31, 2006 4:17 am)
#704 of 747 Re: Mazda B Series [abgager] by abgager Aug 31, 2006 (4:17 am)
Replying to: abgager (Aug 28, 2006 5:05 am) i'm answering my own question here. we cleaned out the throttle body with some xylene in a spray can. residue can build up in there and cause the throttle to stick. it took care of the high-revving problem and also got rid of a rumble in the engine that had been building for several weeks.
#705 of 747 Vacuum hose routing for 1987 b2600 by brucerdn Sep 04, 2006 (2:17 pm)
Hi Folks   Wondering if anyone has any information about what hoses connect to the carb,and where. I just put a new carb on and had some help and can't figure out what hose goes where. Help please Buck
#706 of 747 Re: b series engine swap to a 350 small block [chad4] by gferguson Sep 26, 2006 (2:58 pm)
Replying to: chad4 (Jun 11, 2005 11:06 pm) Did you take this any further ? I'm also considering it for my 84 B2000, make kind of a rat rod out of it. From what I've read on line, it may make more sense to do a Ford 302 swap, lighter engine and plenty of after market parts to soup up the motor. I plan to go with the auto trans, less linage issues than a 4 spd or 5 spd. Some of this info is from the RX7 V-8 swap blog sheets, but may be good advice for a B2000 also.
#707 of 747 B2600i 1993 Fuel Sender Unit by snowshoe1 Nov 09, 2006 (2:54 pm)
I'm desperately seeking a fuel sender unit for my 1993 cab plus B2600i 4x4. The fuel tank itself is readily available but not the sender unit, this must be an extremely rare piece. I have been unsuccesful finding an aftermarket unit and the dealer price is $800.00 after taxes as they won't separate the fuel pump from the sender unit. The problem with my current sender unit is both fuel lines rusted off/broke flush with the top of the sender where it connects to the fuel tank. Anyone have a tip?
#708 of 747 May I have your... by kcram HOST Nov 13, 2006 (7:00 pm)
As you may have noticed, we are reorganizing the Forums to allow better focus and easier searching when you have a particular problem or comment about any given vehicle. We ask that you check the new discussions that you can find at the Group page, linked below. This discussion will not be closed/deleted, so you can still post and search for information in it.   If you don't see a discussion in the group appropriate to your question or comment, start a new one, or send me an email, and I'll point you in the right direction!   Mazda B-Series Group   Thanks! kcram - Pickups Host
#709 of 747 2000 B2500 PU Heater problems by bedinotti Nov 16, 2006 (2:07 pm)
My 2000 Mazda PU model B2500 heater does not work. Last year it was intermittent in that I could leave the heater switch on and restart the engine and it would sometimes work, but no longer. Mazda wants $91 just for an analysis. Does any one have a repair manual they would like to sell or perhaps would be willing to fax the heater diagram/wiring. I took the dash apart but I could not find the problem - the switches all seemed to work. It's getting real cold here in upstate NY so any help or information would be much appreciated. By the way I could not find a repair manual to purchase - supposedly one will be available in January.   Thanks russellbedinottiverizon.net Replies to this message: lodn31 (Nov 23, 2006 2:48 am) wheelman2 (Jan 26, 2007 11:06 am)
#710 of 747 Re: 2000 B2500 PU Heater problems [bedinotti] by lodn31 Nov 23, 2006 (2:48 am)
Replying to: bedinotti (Nov 16, 2006 2:07 pm) HI I have a 94 B2300 and I think I have the same problem. I was wondering if you have got yours fixed or figured out what is wrong with it? Replies to this message: wheelman2 (Jan 26, 2007 11:06 am)
#711 of 747 Help! I need some Wheels. by ck16 Jan 04, 2007 (7:32 pm)
I am just new to the site and was wondering if anyone knows where I can find some Rims and Rubber used or new for a 2004 B3ooo. Hopefully not to costly as it's just for winter.   If anyone can help that would be great.   Thanks. Ck16

Messages Page 72 of 76 1 ... 69 70 71 72 73 74 75 76 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Pickups Mazda B-Series Mazda B Series