Last post on Feb 24, 2012 at 6:03 PM
You are in the Mazda B-Series
What is this discussion about?
Mazda B-Series Pickup, Mazda B-Series Truck, Truck
#633 of 768 Re: Mazda B Series [pf_flyer]
Jul 11, 2005 (5:38 pm)
My 1998 B2500 pickup on a random basis between shifts of the transmission will not return to normal idle speed but sticks at approx. 2500 rpm. When I come to a complete stop it will return to normal but when I return to the road it will continue to do the same thing unless I fully turn the key off when I am stopped. Evidently this restets something. I have been told that a computer reflash might fix the problem. Anybody have any different ideas what the problem may be or had a similar experience?
#634 of 768 2000 B3000 3.0 V6 Automatic
Jul 24, 2005 (1:08 pm)
When engine is cold, under load, about 1,500 to 2,000 RPM's the engine cuts out. I was told by a Mazda mechanic that the fluid needed changing in the torque converter, but it does it when brake torquing also. Any suggestions? I sprayed the plug wires with water when running and found no problem.
#635 of 768 code 332 low EGR flow
Sep 08, 2005 (6:15 pm)
I have a 1994 B4000 Mazda truck with 4.0 liter and code 332 is set after 10 to 15 miniuts of driving. I have reset the computer by taking the battery cable of and turning the ignition switch on and still the check engine light comes on. I pull the codes and 332 comes up. I replaced the EGR valve and still get the same code after re setting the computer. The symptoms are rus rough and surges at cruising speed. Can anyone help?
#636 of 768 Re: B-3000 Won't turn over [tc5]
Sep 13, 2005 (8:03 pm)
i had a similar problem a few weeks ago.....but my problem was that the truck would turn over like crazy, but wouldn't start. i ended up having 2 sensors (i believe they were a cam sensor and a crank sensor). after having the sensors replace it starts up with no problem. your sensors may be wearing out. hope this helps.
#637 of 768 Re: Mazda B Series [billmoore22]
Sep 14, 2005 (5:52 pm)
I have the same problem with the same model, only the high revving is not random, it's pretty much all the time now.
I just replaced all the plugs and wires - maybe it's worse now.
Previously, a service manager at the dealer said to clean the throttle body of carbon build up. That seemed to help 20k miles ago, but have not tried it again lately.
Sep 20, 2005 (3:34 pm)
I have a 1994 Mazda B2250 SE-5 and it makes a coughing sound when i release the gas. What should i do?
Sep 24, 2005 (10:03 am)
Hi I own a 1989 Mazda B2200 and everything is fine on it except that when my dash lights dont work. And when i push on the brakes, the blinker lights on the front come on, but dont blink...(not that they are supposed to anyway.) i need help cause i cant drive at night with the lights out. any suggestions on this?
#640 of 768 B-3000 V6 4x4 problem
Oct 20, 2005 (8:43 am)
2002 B3000 V6 4x4 when turning switch on dash board into 4 high or 4low I have no reaction. Will not go into 4 wheel drive, indicator lights will not illuminate either.
When turning key to acc. position the 4low or 4high indicators will not illuminate as they should like all other indicators do,(air bag, seat belt , batt, gruise etc...)I have checked fuse panel near drivers door and the one under the hood next to firewall all seems o.k.. Does anyone have any ideas? Or has anyone seen this problem. Would appreciate any and all suggestions. My mechanical knowledge is average.
#641 of 768 Re: code 332 low EGR flow [russ6]
Oct 23, 2005 (12:13 am)
I am not sure if any one has responsed to you but I had the same problem. The two thing that I did to solve it was I also replaced the EGR Pressure Sensor and with 94 there maybe alot of carbon build up in the top end I use some intake cleaner and sprayed it in though the intake and at the egr intake area after that the problem went away you also want to change your oil after you do this.
#642 of 768 Re: programming Mazda B-series ignition Keys [screamer]
Oct 27, 2005 (2:51 am)
Did you ever find out how to do this? I am stationed overseas and there is no place that deals with the keys for my truck. I can buy a blank and have it cut but I do not know how to program it. PLEASE HELP