You are here: Forums SUVs GMC Yukon GMC Yukon and Yukon Denali Problems

GMC Yukon and Yukon Denali Problems

779 messages,  Last post on Oct 31, 2009 at 6:36 AM

You are in the GMC Yukon Forum. Your Hosts are steve_ & tidester

What is this discussion about? GMC Yukon Denali, SUV

Messages Page 71 of 78 1 ... 68 69 70 71 72 73 74 ... 78 Prev Next Last

Go To Msg # Search This Discussion

#701 of 779 Starting Problems by tim117 Mar 15, 2009 (6:41 pm)
Recently I sent my IPC in to a repair shop for the stepper motor replacement / Calibration / Update . The vehicle was running perfectly when I parked it & removed the cluster. Upon re-installing the cluster, the battery was dead and the vehicle would not start. After charging the battery, I tried to start my Yukon again to no avail. After some troubleshooting, the fuel rail had no pressure, ie. the fuel pump was apparently inhibited   Anyone have any ideas why it chose now to quit? I find it unlikely the fuel pump went out at this precise time.
#702 of 779 A good experience by tim117 Mar 15, 2009 (7:01 pm)
After reading many of the posts on this site, I don't know if I'm blessed, lucky, or just an unusual case. I own a 2004 Yukon XL 4.8L loaded with all the bells and whistles but not quite the Denali. I had reservations about the AWD and the fact that a service contract for the Denali was twice as much as my truck. Anyway, five years, 130,000 miles and the only repair I've done is the instrument cluster. I still have the original front brake pads, although I've had a replacement set in the garage for over two years. I refuse to replace them til the pad gets too thin. I just wanted everyone to know that my Yukon has been great, I love driving it, and will continue to drive til the wheels fall off.
#703 of 779 Re: 2005 Yukon Denali XL Lift Gate Problem [domsdenali] by kmbaron Mar 24, 2009 (6:17 pm)
Replying to: domsdenali (May 17, 2008 10:29 am) Did you ever find an answer to your problem. I have the same issue and can't seem to find out why. I know the liftgate lock worked up to a certain point but it quit working and am trying to find out why.
#704 of 779 re: GMC Denali Traction Active problem [Hockeysuitman] by jdlsierra Mar 25, 2009 (12:30 pm)
Replying to: Hockeysuitman (Nov 28, 2008 5:59 pm) I had this same problem and finally corrected it by replacing both front  wheel speed sensors ( about 2 hours labor ) you have to remove the brakes  and rotors to access the sensor. The parts cost $ 54.00 each at Ourisman  Chevrolet, Bowie, Md. Replies to this message: alanddrake (Jun 09, 2009 10:31 pm)
#705 of 779 Re: GMC Yukon Denali Problems [greenhead] by greenhead Mar 25, 2009 (1:00 pm)
Replying to: greenhead (Dec 10, 2008 11:57 am) UPDATE - Replaced body control computer - did not solve the problem. Now I just remove the fuse to keep battery from running down and put fuse in when I need to activate auto ride for trailering. Cannot figure this one out. Dealer said suspension control computer was bad. NOT SO. NEED AN EXTRA ONE? Replies to this message: smallridge (Oct 28, 2009 6:06 am) rsht (Oct 29, 2009 3:01 pm)
#706 of 779 Re: 100,000 mile warranty [johnadoe] by 4king Mar 27, 2009 (11:58 am)
Replying to: johnadoe (Mar 13, 2009 5:48 am) I have a 2003 Yukon XL Denali with 72 months or 100,057miles which ever comes first. I thought I bought the Major Guard for 2200.00 but was sent the Value Guard contract, 72 mos. or 60,000 miles but my card and coverage agreement reads 72 and 100,057? Either way GMC sucks out whenever they can and yes they do sell 100,000 optional service contract plan. Not 100.000 mile warranty "wording"
#707 of 779 The cyl 3 random misfire 2002 yukon Denali by 02gmcyukon May 19, 2009 (2:43 pm)
Well well well I have a Random Misfire so far I have done tune up wires fuel injector cleaning,throttle body and intake.Once you drive above 50 MPH and stay above that for about 10 Min check engine flashes then stays on scan it and the same code What am I missing hear.
#708 of 779 Re: Steering Wheel Vibration [jallard] by leetho May 21, 2009 (4:25 am)
Replying to: jallard (Jul 09, 2008 7:10 pm) I have a similar problem with my 2004 Denali, vibration in the steering wheel between 1500 - 2000 rpm and 50-55 mph. Had the vehicle at the dealership twice and they still cannot figure out the problem. Just changed the rims to 22 inch, still the same problem. They were hoping this would have solved the problem. Now I'm in a battle with them because they have not clue what to do.   HELP! Replies to this message: rsht (May 21, 2009 8:56 am) jimandnikkiar (Jul 14, 2009 7:08 am) dmacken1 (Jul 14, 2009 6:29 pm)
#709 of 779 Re: Steering Wheel Vibration [leetho] by rsht May 21, 2009 (8:56 am)
Replying to: leetho (May 21, 2009 4:25 am) Some times bad wheel bearing can be one of the cause to wheel vibration; but, in this case have you checked the steering/ball joints first to see if any is worn (have the joints been regularly lubricated)? One other possibility is the wheel alignment, assuming your wheels are balanced, and all joints are solid... Replies to this message: jimandnikkiar (Jul 14, 2009 7:08 am) dmacken1 (Jul 14, 2009 6:29 pm)
#710 of 779 Re: NAV /DVD [rotti92201] by cann1 May 24, 2009 (1:01 pm)
Replying to: rotti92201 (Oct 27, 2006 5:11 pm) I just purchased a '02 Denali XL & it has this noise in the front drivers side that sounds like a rearend bearing noise! Has anyone had this problem with the Denali XL & what was done to fix it?? Replies to this message: bandaidgooz (May 25, 2009 6:07 pm)

Messages Page 71 of 78 1 ... 68 69 70 71 72 73 74 ... 78 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums SUVs GMC Yukon GMC Yukon and Yukon Denali Problems