Ask the Car People.SM


Subaru Crew Problems & Solutions

19285 messages,  Last post on Jun 03, 2013 at 10:22 AM

You are in the Subaru Crew Forum.

What is this discussion about? Subaru Impreza, Subaru Outback, Subaru Forester, Subaru Legacy, Coupe, Sedan, Wagon, SUV


Go to NHTSA to file a safety complaint.
Or call Monday-Friday (8 am to 8 pm ET) (888) 327-4236 TTY: (800)424-9153
 
Your Community Leaders are ateixeira and rsholland.

Messages Page 727 of 1929

#7259 of 19285 Re: Subaru forester (2006) Catalytic Converters [fibber2] by xwesx

Jan 18, 2007 (11:49 am)

Replying to: fibber2 (Jan 18, 2007 7:29 am)
It is probably tripping the P0400 code (that is caused by mixture reading out of spec, is it not?). Mine was tripping that code periodically for 2.5 years and each time I had my emissions inspection performed the tailpipe readings were nearly identical. I have a hard time imagining that the cat was below threshold if this is the case, so I was leaning toward aging sensors. I planned to address it this spring along with a recent P0420 (EGR system) code, but was saved this headache.

#7260 of 19285 Re: cold start up engine squeal [gaucho1] by xwesx

Jan 18, 2007 (11:55 am)

Replying to: gaucho1 (Jan 17, 2007 11:12 pm)
Nah, you would have to hear the sound to know it is definitely not a belt. Completely different sort of squeal. It is not bad bearings that are squealing, just cold... complaints. I should not have thrown that timing bearing bit in my last post as it was completely unrelated and apparently served to confuse the issue. I noted it only to say that the complaints coming from the pulleys (or whichever moving part(s) that tends to do the complaining) do not seem to lead to less longevity.
 
As for the rubber, it does lose elasticity when cold and therefore is more prone to squealing, but again, a different sort of squeal.

#7261 of 19285 PLEASE HELP - MAJOR SAP PROBLEM by missphilly30

Jan 18, 2007 (7:10 pm)

I've lived in an apartment complex for the past four years where I have no choice but to park under very large pine trees. I have a black Subaru Forester. When the spots first appeared, I ran out and purchased bug and tar remover which did nothing. I then tried the infamous clay bar and again, no luck removing the sap. I've tried alcohol (for the sap, not me) and even lighter fluid applied with a Q-tip and NOTHING will take this stuff off my car! I inquired at an auto body shop as to what options I have other than paying for a new paint job and they laughed at me. Now my car is polka-dotted with old crusty sap spots. If anyone has a trick up their sleeve for removing old crusty sap I would be VERY appreciative. Thank you in advance!

#7262 of 19285 Re: PLEASE HELP - MAJOR SAP PROBLEM [missphilly30] by paisan

Jan 18, 2007 (8:02 pm)

Replying to: missphilly30 (Jan 18, 2007 7:10 pm)
Try looking into what they use in Canada. I know my uncle upstate ny found some good stuff from canada.
 
-mike

#7263 of 19285 Re: Subaru forester (2006) Catalytic Converters [fibber2] by gaucho1

Jan 18, 2007 (8:25 pm)

Replying to: fibber2 (Jan 18, 2007 7:29 am)
Steve,
 
Yeah, it's time to take notes.The trouble is doing it at 70(+)mph.
 
Once I get up to traffic speed (or, whatever I think I can get away with), I tend to set the Cruise and let her run. I prefer to stay away from all the "other" nuts on the road, so I adjust the speed to do so, and well in advance of having to jump out of CC.
 
So, adjustments are usually minor. My first warning of "failure" is usually a drop in speed as the CC gives up control. There is no discernible loss in power, no apparent change in mixture, throttle response, etc.
 
Just the damned lights.
 
I tend to stop around every ninety minutes, so there are plenty of 'cycles' during the day's drive.
 
I have now been in the Ft.Walton Beach, FL area for about ten days, now, with no lights. Weird.
 
Hmm.. Speeds locally are stop-and-go traffic, with short cruises up to 55 mph. As usual, I use the gearbox to keep the rpm between 2,500 and 4,000.
 
Gaucho

#7264 of 19285 Re: Subaru forester (2006) Catalytic Converters [gaucho1] by fibber2

Jan 19, 2007 (7:55 am)

Replying to: gaucho1 (Jan 18, 2007 8:25 pm)
Gaucho,
 
Minor point, but unless block temperture drops back down close to ambient when you take a break, it will still be considered one drive cycle. The criteria is that emissions controls have to revert back to 'open loop' status. That is where the engine, cat and oxygen sensors are too cold to do their job properly, so mixture is determined using 'lookup tables'. Once your temp gauge gets to about 3/4 of normal operating temperature (coolent temp of around 150' or so), the system changes from open loop to feedback. At that point, the front O2 sensor's output is used by the ECU to modulate fuel pulses to maintain optimum mixture. In short, the system has to start cold and go thru that important transition to even be considered a cycle.
 
The good news for you is that the recorded error code and the 'snapshot' are all probably still stored data (for 40 cycles). Depending on your ECU programming, the snapshot probably recorded vehicle speed, RPM, throttle position, coolant temp, incoming air temp, calculated engine load, and a whole bunch more. Some autoparts stores like AutoZone will read it out for you. Most just have a handheld, so you will just get the Pxxx fail code, others might be able to print out the snapshot data as well. If you are going to your deal soon they will want to see it as well, so don't have them clear it.
 
Steve

#7265 of 19285 Re: PLEASE HELP - MAJOR SAP PROBLEM [missphilly30] by cusafr

Jan 19, 2007 (8:07 am)

Replying to: missphilly30 (Jan 18, 2007 7:10 pm)
I don't know about Sap, but I have used WD-40 for many things including road tar.
 
If the Sap is thick (like a glob) spray on WD-40 and let it sink in for about a minute. If Sap is light marks, you should be able to spray on and wipe off rather easily.
 
It works great for me. Also, I always wash the car immediately after using.
 
Hope this helps,
 
Let me know,
 
cusafr

#7266 of 19285 Re: PLEASE HELP - MAJOR SAP PROBLEM [missphilly30] by smittynyc

Jan 19, 2007 (8:25 am)

Replying to: missphilly30 (Jan 18, 2007 7:10 pm)
Assuming you haven't damaged the finish with some of the other remedies, I'd recommend trying Klasse All-in-One. It's a cleaner/polish/sealant, and it has removed various stains from my car (especially tar and bugs) that I thought would be there forever.
 
You can only buy it online -- do a Google search and then search for "Klasse" in the Subaru forums for advice on application/use. Good luck!

#7267 of 19285 clock light by psfod3

Jan 19, 2007 (10:14 pm)

I have a 03 forester. There is a storage compartment above the clock I had trouble closing it and I banged it down a few times. My clock works but the light went out. How hard is it to try and check the bulb and conection. Any how to help would be greatly apprieciated.

#7268 of 19285 Re: I need help and am not getting any from Subaru [jessr] by davisrs41

Jan 20, 2007 (1:18 pm)

Replying to: jessr (Jun 28, 2006 12:23 pm)
Every brand has lemons and don't expect Toyota to back you up with a head gasket problem either! I'll never buy another Toyota.
 
I had a Toyota Camry blow a head gasket, suck in coolant and throw a rod right through the oil pan!!!
Talk about an expensive piece of junk scrap metal!
I got $3000 salvage value for that car and it never made it to 100,000 miles.
 
That's when I went to Subaru!!
My '98 Forester has been great, 156,000 mi.
My '97 Legacy LSI just developed the slowly leaking head gasket problem at 165,000 mi.

Messages Page 727 of 1929

To POST a message, please Sign In.

Advertisement

Browse by Category

Browse by Vehicle
   View All Vehicles

Browse by Board
Browse by Topic
View All Topics

Edmunds Community

Advertisement