Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
Wagons Subaru Crew Subaru Crew Problems & Solutions
18373 messages, Last post on Nov 26, 2009 at 7:25 AM
You are in the Subaru Crew Forum. Your Host is kcram
Your Community Leaders are ateixeira and rsholland.
|
Replying to: girlcarbuilder (Jul 04, 2009 6:43 pm) I checked the coil pack no flash marks of carbon scaring. Plugs are brand new, swapped cables, problem did not move. Tried Lucas additive, code P0301 still popped up. I do not know where to get a good coil pack to try out. The crankshaft sprocket has on the back something that looks like a bicycle gear. The tips are shiny, which tells me it was rubbing something. The teeth of the sprocket will be shiny (that is what the belt ride on). I think that the hydraulic tensioner pulley (which showed slight wear) was coming in contact with the gear spokes.
|
|
|
|
|
Replying to: phil2000 (Jul 04, 2009 8:05 pm) For starters, if that is the original tensioner, at almost 300K, it is past due for tossing knowing the few I have dealt with. Check Rockauto.com for the best price. Get the gear to compare to a new one at an auto parts store. If it looks different, replace it. Keep the old one for now, tag it: not a confirmed defective part yet. Wish I could physically look at it. Could still have a magnetism problem with it, but I suspect problems from this area to be less likely. Usually it is go/no go. Now, lets return to the coil. No external flashovers visible. Being a multiple coil pack, I am wondering if it is breaking down internally. If it is original, I highly suspect it to be: Years ago, 100K was doing good. The Toy had 180K, but the misfire problem had been around since 150K. As you gather, you are almost twice that now. Maybe there is a wrecked unit in a junk yard. I am seeing them new available at Rockauto for about $150, ouch. which means people are buying them: does not mean they are failing though. Educated guess, based on working on too many during the years. I would say somewhere between 50- 75% of being right. That low, because Subaru quality has proved me wrong before, but the 2000 if made in USA is also most likely made in USA parts. Reason why the next new car is coming from Japan. This is what I would look at real hard. Hopefully, but not likely, a valve is sticking from gunk or beginning to burn/warp. This may have to be ruled out over time. Good oil and that valve job a while back should rule that out. Compression readings do not help the problem from way back then. I wonder what those readings are now. Another thought would be to see if you could lay your hands on a real time code reading system like Autotap.com has. You need to be able to see what else the computer might be able to tell you that is not tossing out a code. From what I recall, the code comes up within a 100 mile run, which forces it to be dealt with. Yup, I agree with you about emissions. I am still amused by the rebates placed out there. 86 Toy may run well, but I seriously doubt it would pass an OBD II computer pain in the butt.
|
|
|
Hi All, I'm leasing an 09 Impreza premium.... Since day one there has been a lot of vibration in the shift knob, even when stopped and idling. Is this normal for the model or is something up? Thanks in advance |
|
|
|
|
Replying to: jasvic (Jul 08, 2009 12:29 pm) I suspect the clutch assembly or something is out of balance if the engine is running fine. No codes being tossed out? Like a misfire code? |
|
|
Is replacing a (passenger side) seat belt a do-it-yourself project? My 2-yr old lab/mix decided it was better than his chew toy.
|
|
|
Replying to: jasvic (Jul 08, 2009 12:29 pm) I chalk it up to the flat-four engine... which isn't the smoothest thing going..
|
|
|
|
|
Replying to: smudgejet (Jul 08, 2009 2:38 pm) Also, there is JC Whitney you can google. One of our units has belts from there and they have worked just fine for the past 150K.
|
|
|
|
|
Replying to: kyfdx (Jul 08, 2009 4:44 pm) Generally this does not happen often, but it does. H-4's are more prone to problems with this especially if someone was sleeping on the job when they were supposed to be balancing! Why? The opposing piston is the counter weight. Where as in another configuation, crankshaft throws and sometimes additional counterweight shafts deal with this problem more. You still have to balance them as needed. So far, there are 3 Subaru's currently in service that have not had this problem. 1 at 170K, another 215K and the last at 240K. Engine sizes 2.2, 2.5L. Neither have any in the past service/ownership. But when it comes to any engine being assembled, it can happen. My biggest concern about an engine like this is overall lifespan reduction of the engine and when that heaviest piston begins to toss out a misfire code with the addition of any other varibles that become a problem. Not sure what you could do to resolve this issue. dealer would probably blow it off as being "normal.' I would not buy that answer, but recourse is hard to prove short of a complete teardown. That is not worth it.
|
|
|
Replying to: girlcarbuilder (Jul 09, 2009 6:14 am) I'll check around at the junkyards and with JC Whitney for the best price. |
|
|
Replying to: smudgejet (Jul 08, 2009 2:38 pm) |
|
You are here:
Forums
Wagons Subaru Crew Subaru Crew Problems & Solutions
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2010 Subaru Impreza
2010 Subaru Outback
2010 Subaru Forester
2010 Subaru Legacy
Browse by Board
Browse by Topic
Today's Chats
