Ask the Car People.SM


Dodge Ram Accessories and Modifications

332 messages,  Last post on Apr 12, 2011 at 1:59 PM

You are in the Dodge Ram-2010 and older Forum.

What is this discussion about? Dodge Ram Pickup 1500, Dodge Ram Pickup 2500, Dodge Ram Pickup 3500, Truck

Messages Page 34 of 34

#323 of 332 Attention 2009-10 Ram 1500 Laramie owners by KCRam@Edmunds HOST

Feb 01, 2010 (5:15 pm)

An aftermarket company is seeking an owner of a 2009-2010 Dodge Ram 1500 Laramie to test the side view mirror’s memory function. The company will provide the new mirror to the volunteer who will be able to keep it after helping with the test. If you are interested, please email sylviaedmunds.com with your phone number and mailing address.
 
kcram - Pickups/Wagons Host

#324 of 332 RAM 1500 door adjustments by minardi

Feb 10, 2010 (1:21 pm)

Anyone know if the driver's door on an '07 RAM 1500 Quad cab can be adjusted to seal tighter? Had some body work done after sideswiping a guard rail and wind noise is sometimes really bad. If I pull on the door while driving, it reduces the noise a lot.

#325 of 332 Re: RAM 1500 door adjustments [minardi] by KCRam@Edmunds HOST

Feb 10, 2010 (5:16 pm)

Replying to: minardi (Feb 10, 2010 1:21 pm)
Take the body shop manager for a ride and demonstrate it... from your description, they need to realign the door, and it should be covered as part of the previous repair.
 
kcram - Pickups/Wagons Host

#326 of 332 01 dodge ram engine swap by nathanbauer84

Feb 20, 2010 (1:50 pm)

#327 of 332 01 dodge ram engine swap by nathanbauer84

Feb 20, 2010 (1:44 pm)

I have an 01' Dodge Ram 1500 with the 3.9L v-6 and was wondering if a 5.7 or 5.9L V-8 would bolt up to the tranny. The V-6 has the same bore stroke and compression ratio as the V-8s but not too sure if they would have the same bolt pattern on the tranny. If u have any info please e-mail me at nathanbaueratt.net

#329 of 332 Re: 2002 Ram 1500, 4.7 engine swap to 5.7 HEMI [katthomas] by jfuentes

Jun 21, 2010 (6:32 pm)

Replying to: katthomas (Apr 12, 2007 3:42 pm)
From reading around ( i wish to also swap up) the transmision should hook up, you need a wiring harness from the hemi truck, the pcm, the tcm and ecu , the tcm has to match the style of your truck or 4x4, you also need new engine mounts, the easiest way to go about this is to use a hemi and parts from a 2003 Hemi...should be around 3000 for everything, also exhaust needed and the 03 uses a different style throttle body, uses wire not cable like the 02, so either convert your accelerator or throttle body to use cable

#330 of 332 Re: 2002 Ram 1500, 4.7 engine swap to 5.7 HEMI [jfuentes] by dustyk

Jun 25, 2010 (6:56 pm)

Replying to: jfuentes (Jun 21, 2010 6:32 pm)
The 4.7 and the 5.7 Hemi are the only two engines that currently use the 545RFE transmission. I'm not completely sure, but i believe the rear engine apron bolt pattern is the same.
 
However, there is a difference between a 545RFE in the 4.7 and the Hemi. For one, I believe the input shaft is bigger.
 
Regards,
Dusty

#331 of 332 2004 Ram Quad Cab by latwood

Sep 18, 2010 (6:09 pm)

I was wondering if anybody has installed a cool box air intake on they're 4.7 mag. and what results they got. I already have a flowmaster exhaust..I thought about Bosch plugs too...look'n for a little more power without changing the chip or cam..thanks!

#332 of 332 Re: Widening look for wheels. Part that goes onto axle? [levic] by thenoah

Apr 12, 2011 (1:59 pm)

Replying to: levic (Jan 05, 2008 8:42 pm)
aaaand they are a horrible idea in most circumstances, unless your tires rub somewhere all the spacers will do is cause increased wear on suspension components and wheel bearings. The "look" isn't worth the pain.

Messages Page 34 of 34

To POST a message, please Sign In.

Advertisement

Browse by Category

Browse by Vehicle
   View All Vehicles

Browse by Board
Browse by Topic
View All Topics

Edmunds Community

Advertisement