Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
Sedans Oldsmobile Aurora Oldsmobile Aurora Maintenance & Repair
4283 messages, Last post on Nov 25, 2009 at 10:33 AM
You are in the Oldsmobile Aurora Forum. Your Hosts are pat & karens
| my car has changed from miles to km how do i change it back | |
|
Has anyone tried raising the front end of their Aurora by fabricating spacers and placing them at the top of the struts? Or, has anyone raised their front end by any means? Ken |
|
|
Replying to: KarenS (Aug 31, 2001 7:39 am) |
|
I need to know how to change an alternator on a 1995 aurora
|
|
|
|
|
Replying to: smartass1 (Feb 28, 2009 9:31 pm) 1. Rear seat cushion. 2. Negative battery cable. 3. Upper radiator shroud. 4. Right and left cooling fans. 5. Accessory drive belt from P/S pulley then generator. 6. Top alternator bolts, disconnect cable and regulator connector. 7. Ground strap and P/S line bracket to gain access. 8. Lower generator bolts (raise vehicle). 9. Lower radiator hose (drain radiator). 10. Air inlet duct. 11. Generator through top left side of engine compartment. INSTALL OR CONNECT 1. Generator through top left side of engine compartment. 2. Air inlet duct. 3. Lower radiator hose. 4. Lower generator bolts. 5. Ground strap and P/S line bracket. 6. Generator Mounting Bolts. Tighten o Front Studs to 38 N.m (28 lb. ft.) . o Rear Bolts to 47 N.m (35 lb. ft.) . 7. Generator Output Terminal Nut. Tighten o Nut to 20 N.m (15 lb. ft.) . 8. Voltage regulator connection. 9. Accessory drive belt. 10. Right and left cooling fans. 11. Upper radiator shroud. 12. Negative battery cable. 13. Rear seat cushion. 14. Fill cooling system. |
|
|
|
I just bought this car and the drivers outside door handle doesnt work. I realize that the door panel needs to be removed and I would like to know exactly how to do this.
|
|
|
|
|
Replying to: cadillacraig (Mar 01, 2009 2:27 pm) 1. Bezel finish cover from door handle bezel by unsnapping upper tab with thin-bladed tool. 2. Door handle bezel by removing one screw, unsnapping bezel and lifting it off and over door handle. 3. Two screws from lower door under map pocket. 4. Trim panel by lifting up on trim panel to disengage hooks on backside of panel. 5. Electrical connectors. INSTALL OR CONNECT 1. Electrical connectors. 2. Trim panel by engaging hooks on backside of panel into door inner panel. 3. Two screws under map pocket. 4. Door handle bezel by snapping into position and one screw. 5. Bezel finish cover. |
|
|
|
|
Replying to: Mr_Shiftright (Mar 01, 2009 2:31 pm)
|
|
|
|
|
Replying to: cadillacraig (Mar 01, 2009 5:38 pm)  Of course you will. Ah, door handle parts--that could be very tough. I'd say google the internet for Oldsmobile parts, then try eBay search, then see if someone on your local craigslist is parting out an Aurora, then try a large wrecking yard in your area, or a "Pick a Part".
|
|
|
|
|
Replying to: Mr_Shiftright (Mar 01, 2009 5:57 pm)
|
|
You are here:
Forums
Sedans Oldsmobile Aurora Oldsmobile Aurora Maintenance & Repair
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2003 Oldsmobile Aurora
Browse by Board
Browse by Topic
