6928 messages,
Last post on May 13, 2013 at 7:56 PM
You are in the
Honda CR-V Forum.
What is this discussion about?
Honda CR-V, SUV
Go to NHTSA to file a safety complaint.
Or call Monday-Friday (8 am to 8 pm ET) (888) 327-4236 TTY: (800)424-9153
#6720 of 6928 Re: 40,000 mile service on a 2007 CRV 4WD LX [dadschum]
by kyfdx HOST
May 16, 2011 (8:58 pm)
I think the WRG2 is the updated version of the WR (latest and greatest)..
What I like about them with the CR-V, is not only did I get wintertire-like snow traction, they were better handling dry-road tires than any of the crappy OEM tires that Honda uses.... In the size my CR-V used (205/70-15), they were H-Rated, vs the S-rated tires that came on it..
It was a win-win... except for the price..... shewwww (still, worth it).
#6721 of 6928 Re: 40,000 mile service on a 2007 CRV 4WD LX [kyfdx]
by circlew
May 17, 2011 (3:33 am)
The 245/70 Kumho Road Ventures make the '08 handle like a Corvette. (The tire mechanic worried a little about the fit but no problem at all.)
The steering is already phenomenal but I've got to thank Honda for the worst tires ever that made the transition to real rubber an epiphany of great chassis response!
Regards,
OW
May 19, 2011 (5:59 am)
How hard is it to replace a drive belt on an '02 CRV, 4WD? From what I've read it also involves removing a splash shield of some sort? Have 84K miles and think it's time. Plan to replace the tensioner pulley also since it is starting to wear groves in it. Any suggestions?
#6723 of 6928 Re: '02 Differential Noise [Mr_Shiftright]
by fussycrvowner
May 19, 2011 (6:02 am)
I know it's long after the original post. I found the source of the noise while replacing the rear brakes. The backing plate has started to rust through and is rubbing on the discs when making sharp turns. I guess I'll wait until it becomes a problem.
#6724 of 6928 Re: '02 Differential Noise [fussycrvowner]
by Mr_Shiftright HOST
May 19, 2011 (8:08 am)
Hmmm...can't you bend it out of the way a little bit?
#6725 of 6928 Re: '02 Differential Noise [Mr_Shiftright]
by fussycrvowner
May 19, 2011 (11:45 am)
Good point. The issue arises because there is some sort of a raised ridge around the section where the parking brake assembly sits. Some sort of a way to seal it off? I tried to sand it a bit but am afraid to bend it for fear of it breaking off. That's where the rust holes are.
#6726 of 6928 Re: '02 Differential Noise [fussycrvowner]
by Mr_Shiftright HOST
May 20, 2011 (9:41 am)
Yeah I can't see it so I hesitate to advise you on a jury-rig here.
#6727 of 6928 Screeching Door Locks
by cannell3
May 22, 2011 (9:33 am)
My daughter's 2007 Cr-v has screeching door locks. When she starts off and the automatic door locks activate, there is a noticeable "screech". Is anyone out there familiar with this problem? Thank you.
#6728 of 6928 Re: Screeching Door Locks [cannell3]
by Mr_Shiftright HOST
May 23, 2011 (10:12 am)
Didn't see any TSBs on this issue. You'll probably have to pop off the door panel or panels and see what is interfering in there--some metal to metal contact perhaps.
#6729 of 6928 Re: Drive Belt Replacement? [fussycrvowner]
by lou777
Jun 17, 2011 (12:50 pm)
I did this on my 99, or at least my mechanic did. You are going to replace the water pump too since the engine will be half torn down anyway. I paid less than anyone I could think of who is not a mechanic. My mechanic charges $30/hr
8=$240 and I got the parts with employee discount approx. $500
LMK how you made out,
Lou