Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
SUVs Honda CR-V Honda CR-V Maintenance and Repair
6432 messages, Last post on Nov 07, 2009 at 4:46 PM
You are in the Honda CR-V Forum. Your Hosts are steve_ & tidester
Your Community Leader is varmint.
| I've jost got my new CRV for three months. The current milage is about 5000 miles. A couple of days ago I started feeling vibration on the steering wheel and the driver's seat. The problem got worse when I reduced speed on highway. Can anyone please give me suggestions on what the problem might be and how to fix it. Really appreciate. | |
|
Replying to: pat78 (Oct 24, 2008 8:11 am)
|
|
|
Replying to: kiawah (Sep 30, 2008 3:20 pm)
|
|
|
Replying to: washby (Oct 24, 2008 1:22 pm) If you have a V-something (6 or 8 cylinders), then Bank 1 is the V-bank which has cylinder 1 in it, and Bank 2 is the other bank. Sensor 1 and sensor 2 are before and after that cat, just as before. The engine computer, uses the feedback from the oxygen sensors to adjust the fuel mixture for optimal performance. I don't know the crv reset specifics, but typically it takes a number of start cycles and miles of driving before the computer will automatically reset the service light. The computer doesn't turn the light on right away with the first out of spec failure, and it doesn't turn it off right away. This is assuming you didn't drive around a lot with the service light on, dumping excess unburnt fuel into the cat converter, and ruining it. If you fixed this quickly after having the initial light, you should be in okay shape. Give it a couple days of driving, and if it isn't off by then, go back to whereever you went to have it read, and have them read the codes again, and then reset the errors. That way you'll be able to see if you get a new/different set of error codes. |
|
| this whole time ive been driving my spare car and havent been using the crv and yes it is a straight 4 so im guessing it has two o2 sensors and i changed the first 02 sensor (using a universal Bosch sensor where you have to piece together the wires with the old harness-$60 instead of $200) but the light is still on. I had autozone check the codes and manually reset them and the light stayed off for a few seconds and then came back on after i reversed and stepped on the gas. The same is true after I disconnected the battery from the car and let it sit powerless for about an hour. The codes are still reading the same thing ODBII PO134 code Sensor No Activity Bank1 Sensor1 and PO135 Code P0135 --Oxygen Sensor Heater Circuit Malfunction. I am beginning to think that maybe the problem wasnt the original O2 sensor itself but the harness that connected it to the system which I reused when i spliced the wires using the in-box connector Bosch provides you with. It is either than or the harness itself leading to the engine or it could be something blown in the fuse box. Do you know the exact fuse that powers the sensor heater circuit/02 harness that sends the signals to the computer? | |
|
Replying to: washby (Sep 30, 2008 2:46 pm) |
|
|
Replying to: phisher (Oct 24, 2008 11:45 am)
|
|
|
Replying to: pat78 (Oct 30, 2008 7:18 am) |
|
I got the maintenance codes checked in my 2004 Honda Crv and they were ODBII PO134 code Sensor No Activity Bank1 Sensor1 and PO135 Code P0135 --Oxygen Sensor Heater Circuit Malfunction. How is it that you replace the Oxygen Sensor Heater Circuit? Does anyone know where the Oxygen Sensor Heater Circuit is located and what they run for?
|
|
|
Replying to: washby (Oct 31, 2008 11:38 pm) The oxygen sensor normally is in an extremely hot environment, monitoring the exhaust gases. When you first start a vehicle, the exhaust gas is comparatively speaking cold, and hence the oxygen sensor is giving erroneous readings as it is not working in the hot environment it normally works in. What the heater circuit does, is when starting a cold engine it heats up the oxygen sensor....so it gets up to working temperature faster, and allows your engine computer to adjust the correct fuel mixture quicker.
|
|
You are here:
Forums
SUVs Honda CR-V Honda CR-V Maintenance and Repair
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2010 Honda CR-V
Browse by Board
Browse by Topic
Today's Chats
