You are here: Forums SUVs Jeep Cherokee and Jeep Grand Cherokee Jeep Grand Cherokee Maintenance and Repair

Jeep Grand Cherokee Maintenance and Repair

4591 messages,  Last post on Nov 09, 2009 at 8:17 AM

You are in the Jeep Cherokee and Jeep Grand Cherokee Forum. Your Hosts are steve_ & tidester

What is this discussion about? Jeep Grand Cherokee, Jeep Cherokee, SUV

Messages Page 436 of 460 1 ... 433 434 435 436 437 438 439 ... 460 Prev Next Last

Go To Msg # Search This Discussion

#4345 of 4591 Re: why the shaking [soxfansc] by trickster Dec 06, 2008 (12:24 pm)
Replying to: soxfansc (Nov 26, 2008 7:29 pm) The shaking your getting is more than likely the fact that you re-installed your front drive shaft 180 degrees from it's original position. Also inspect the drive shaft to see if any of the small balance weights have knocked off recently. Are the universal joints in good condition, and no parts missing? Most shaking in the front end can be attributed to lost tire balance weights, mud or dirt on the inside of the tires, separated or worn tires, unbalanced front drive shaft or a worn front end dampener shock.   I hope this helps you, and good luck m8.
#4346 of 4591 Re: 96 jgcl front diff pinion gone [trickster] by tuggajb Dec 06, 2008 (2:45 pm)
Replying to: trickster (Dec 06, 2008 11:15 am) if you replace the ring gear you also have to replace pinion gear as these are matched sets Replies to this message: trickster (Dec 06, 2008 3:07 pm)
#4347 of 4591 Re: 96 jgcl front diff pinion gone [tuggajb] by trickster Dec 06, 2008 (3:07 pm)
Replying to: tuggajb (Dec 06, 2008 2:45 pm) The pinion does not have to be replaced if your replacing the gear nest with the original gear ratio. If your swapping out gear ratios ie: 373 ratio to a 410 ratio, then yes, everything must be changed to match each other. The diff in your particular year is more than likely a spicer35 in the front, and a spicer 30 in the rear. These are the most common setups in jeep products. Talk to any gear centers, or driveline centers in your area about replacing the gear nest in your diff. By the way, i've replaced 20+ gear nests over the years, and never had to replace the pinion; unless the pinion was damaged, or needed replacing.   I hope this helps you, and good luck m8.
#4348 of 4591 Re: 97 JGC V8-Internal Transmission Failure? [klsflyer] by trickster Dec 07, 2008 (9:27 am)
Replying to: klsflyer (Nov 22, 2008 1:20 pm) I hope you got your tranny fixed, but if not then..... I cannot see internal transmission failure, because you state that in fact there is smooth gear transitioning. I assume that other than using more fuel to get you where you want to go everything else is fine regarding the transmission. There is a governor sensor located inside the transmission pan, and that needs to be changed. I would have a compentent shop or dealership do the work, (it really is messy work), and since your at the point, changing your transmission filter is a very good idea (about $30 ). A good idea for the first 2 weeks after the fix, is to put cardboard on the ground under the transmission. Or just keep an eye on it. Transmission pans have a tendency to leak from the bolts loosening off, and will need to be re-torqued to spec, unless you ask them to use lock-tite on the bolts.   I hope this helps you, and good luck m8.
#4349 of 4591 Re: 2001 Jeep GC Heater problems [hecmol] by mclaxton Dec 20, 2008 (6:04 pm)
Replying to: hecmol (Dec 05, 2008 6:58 am) if your fan works with the air on and your problem is no heat then it is the flaps in the blower housing that are not directing hot air into the cabin. had the same problem and i went to this forum and was directed to a company called heater treater. they sell a product that is specifically made for this problem. was easy to do and only took 45 min and cost $145 heater has been working great since, it comes with full idiot proof instructions, hope this helps. Replies to this message: smokebee (Dec 21, 2008 12:36 pm)
#4350 of 4591 Re: 2001 Jeep GC Heater problems [mclaxton] by smokebee Dec 21, 2008 (12:36 pm)
Replying to: mclaxton (Dec 20, 2008 6:04 pm) Start engine--run til hot--feel the two heater hoses near where the enter the firewall connections. If both are equally hot the water is circulating thru the heater core. Kill engine.Drop the golve box lid all the way down. You will need to release the rubber stops and flex the two pins on the top of the lid so that it will come all the way down. At the left side you will see a squarish black box attached to the blower housing.Remove the two srews holding it. Lift the housing away from the blower house(leave wireing connected). Pay attention to the shaft alignment. Turn the switch on. Set air to floor. Manipulate the heat control. If the shaft ring does not move within the motor housing do this. remove the 4 screws on the housing. Slowly lift the side off to expose the gears. Remove the three regular gears to expose the worm gear.Again manupilate the heat control. If the worm gear does not move.---Remove the tiny motor and turn the screw by hand to free it up. Again see if the motor will run. If it runs--- replace everthing. Reattach the motor housing to the blower housing and try it out again. That fixed my problem at no cost--just time and frustration Good luck--Smokey Swann---Tx
#4351 of 4591 Stalled out by joesjeeps Dec 25, 2008 (4:10 pm)
I have a 1995 Grand Cherokee w/ EFI, 5.2, quadratrac. I drove it approximately 30 miles today and it ran fine but when I took a lefthand turn three blocks from my house it just died. I tried to start it and I get the starter turning but it won't turn over. I thought it might be the fuel filter so I let it sit for about an hour thinking that if it was clogged the sediment might settle but got the same result. Any suggestions? Replies to this message: clipkarn (Dec 25, 2008 4:42 pm) joesjeeps (Dec 26, 2008 7:57 am) clipkarn (Dec 26, 2008 12:02 pm) and 2 more... neb1997 (Dec 30, 2008 8:58 am) joesjeeps (Dec 31, 2008 7:58 am)
#4352 of 4591 Re: Stalled out [joesjeeps] by clipkarn Dec 25, 2008 (4:42 pm)
Replying to: joesjeeps (Dec 25, 2008 4:10 pm) Did the engine turn over? Was voltage near 12 with the key on? If the engine turned with the starter but the volts were below about 10, you may not be getting ignition, and fuel might also be a factor if voltage is low. Sorry I can't tell you for sure what to poke at.   Anyway, at least you were close to home. Merry Christmas.   Clip Replies to this message: joesjeeps (Dec 26, 2008 7:57 am) clipkarn (Dec 26, 2008 12:02 pm) joesjeeps (Dec 29, 2008 8:56 am) and 1 more...
#4353 of 4591 Re: Stalled out [clipkarn] by joesjeeps Dec 26, 2008 (7:57 am)
Replying to: clipkarn (Dec 25, 2008 4:42 pm) The engine does not turn over and I just replaced the battery two days ago. Replies to this message: clipkarn (Dec 26, 2008 12:02 pm) joesjeeps (Dec 29, 2008 8:56 am) clipkarn (Dec 29, 2008 5:11 pm)
#4354 of 4591 2001 Grand Cherokee, locking wheels..... by cesarherna Dec 26, 2008 (8:35 am)
Hello, I am trying to install a different bolt pattern rims to my Jeep, so I get a set of wheel adapters on the internet, but the wheels get lock with the adapters on it and is impossible to move any wheel by hand and not even trying driving the car, the size on the adapters are fine, everything fit perfectly and I don't see any reason to what is happening. Is any wheel sensor locking the brake system? Has anybody seen this before or any possible suggestion?   Thank you

Messages Page 436 of 460 1 ... 433 434 435 436 437 438 439 ... 460 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums SUVs Jeep Cherokee and Jeep Grand Cherokee Jeep Grand Cherokee Maintenance and Repair