Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
SUVs Jeep Cherokee and Jeep Grand Cherokee Jeep Grand Cherokee Maintenance and Repair
4609 messages, Last post on Dec 02, 2009 at 6:10 AM
You are in the Jeep Cherokee and Jeep Grand Cherokee Forum. Your Hosts are steve_ & tidester
| OK, a few weeks ago, prior to needing rear defrost in WV, I was loading stuff into the hatch and noticed as I looked up at the window that the piece that attaches the wires to the grid lines that run across the window to defrost was melted as well as the wires. We had not used rear defrost for a while and do not know where to begin to fix it. Is this a defective problem that Jeep should fix? Please help! Frosting every morning!!! | |
|
|
|
The head gasket in my 90 Jeep Cherokee Limited has blown for good now and I need a new engine. Found a wreck 94 Cherokee for a super great deal that has an engine with 75,000 miles on it. Wondering if they are compatible? Some how I have a love-hate relationship with this car and KEEP putting money into it....
|
|
|
Hello too all: I have a 2005 Grand Cherokee Ltd. The tire pressure monitor light comes on & the dealer suspects one of the sensors is the problem. In my opinion this feature is nothing more than a pain in my back side. It appears as though the monitor circuit is fused, (10A), but what I don't know is if the fuse can be pulled w/o creating a tsunami of additional problems. Any help would be appreciated.
|
|
|
Replying to: vincerg (Nov 05, 2008 5:14 pm) The best solution is to disable the output of the sensor. My guess is the dealer wants $400 or more to fix it. Because it is related to safety you might have to do it yourself. A mechanic might not do it. I'm 99% sure dealer won't do it. First, get a Haynes manual and look for repair info or wiring diagrams. The output of the sensor is probably a digital (1 or 0) input to your Body Control Module (BCM). The BCM reads sensor and turns the light on or off. NOTE: ALWAYS HAVE (-) OF BATTERY DISCONNECTED WHEN MANIPULATING CONNECTORS OR WIRES, HOOKING UP A TEST PROBE, ETC. You need to measure voltage output at the sensor when warning light is On and Off. If the values switch between 0V (Gnd) and 12-14V (battery) continue. Otherwise stop. If sensor module uses data bus to communicate with BCM, you cannot disable it and fake out the BCM. You will have to replace the sensor module. If the light is on for 0V, you will have to pull the input high (battery) to fake out the BCM. It's very possible that disconnecting output of sensor to BCM will be sufficent. If you measure (battery) when light is on, you will have to find a way to ground the input to the BCM. In either case the sensor output is left disconnected. Use a clip lead to test your solution. If OK, implement a permanent solution. You will have to backprobe nearby connectors. You will need a voltmeter probe with a long thin point. After you find a good location, you will have to improvise a connection. Test drive alone (no family) where there is little or no traffic. |
|
|
Replying to: sassafrasnanc (Nov 05, 2008 4:56 pm) Unless you know sellers, what are the odds of finding a 94 engine with less than 100K miles ? |
|
i have 98 jgc i get no fire from coil .i have changed coil ,tps sensor,map sensor,crank positin sensor,and main computer, still will not start...prior to this it would run but very rough and used the heck out of gas.i chaned everthing thats has come up on code reading...this s crazy
|
|
| I installed new tranny cooler lines on my 1989 Jeep Cherokee Pioneer 4.0 liter. The new lines had slightly different pressure fitting ends than the old ones. There are 4 shiny metal tabs inside whereas the old had none and used a plastic collar and snapped onto a 2 tabbed larger collar. I attempted to install without the plastic but couldn't get a seal. I started the engine and tranny fluid seeped out of the pressure fitting. They don't seem to lock into place. What am I doing wrong and how do I fix it? | |
|
Replying to: rbirm (Nov 08, 2008 11:09 am) |
|
|
Replying to: rbirm (Nov 08, 2008 11:09 am) I looked at my 97 shop manual. Maybe this info will help. The first thing they recommend is a test for spark at the coil. 1) Disconnect igniton coil secondar from center tower of distributor cap. Hold cable terminal approximately 1/2 in. from good engine ground. 2) Crank engine with starter and observe cable terminal for a steady arc. If steady arc does not occur, inspect the secondary coil cable. Also inspect distributor cap and rotor for cracks or burn marks. Repair as necessary. If steady arcing occurs, connect ignition coil calbe to distributor....(and then they discuss observing arc at ignition wires, etc. If you really like the car try to buy a shop manual. Some other thoughts. 1) You must be able to measure fuel pressure 2) Wiring/connectors between engine computer and ignition components? 3) What about the automatic shutdown relay ? 4) The Body Control Module (BCM) and engine computer must communicate to start. Replacing BCM requires reprogramming BCM or it won't start. Is there a similar issue when you replace the engine computer? If you fix it, let us know what it was. |
|
You are here:
Forums
SUVs Jeep Cherokee and Jeep Grand Cherokee Jeep Grand Cherokee Maintenance and Repair
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2011 Jeep Grand Cherokee
2001 Jeep Cherokee
Browse by Board
Browse by Topic
Today's Chats
