Sign In Join 



Ford Ranger Maintenance and Repair

2825 messages,  Last post on Nov 27, 2009 at 6:47 PM

You are in the Ford Ranger Forum. Your Host is kcram

What is this discussion about? Ford Ranger, Truck


Messages Page 278 of 284
1
...
275
276
277
278
279
280
281
...
284
Prev
Next
Last
Go To Msg #
Search This Discussion

#2763 of 2825
1990 Ford Ranger 4 cylnder will not start by cougan
May 23, 2009 (5:02 pm)
Reply
My ranger will go through the motions of starting, but it has no fire. I had one of the power packs checked and it was fine. Also I have no power going to my fuel pump. More specifically, I have no voltage on the safety switch on the passenger floor board. I think that my problem is either the ecc relay or the emc. My question is, where is the ecc relay? I found one relay behind the glove box, which I think is the fuel pump relay, but I am nor for sure. Can someone please tell which relay it is behind the glove box and where is the ecc relay so I can test to see if it supplying voltage to the ecc. Or if you have any other recommendation that will help me troubleshoot the problem, I would appreciate it.
#2764 of 2825
Can't get my 95 Ford Ranger into Drive by mannymiranda21
May 26, 2009 (11:30 am)
Reply
I started my truck this morning to head to work and foun that I am unable to shift it into drive, or shift in general. It has locked up. My truck starts fine without a problem, but I just cant get it to shift. Where should I start looking?
#2765 of 2825
97 mazda b2300 2.3l by tdaniel
Jun 06, 2009 (2:19 pm)
Reply
i started it up and teaching my son how to drive, he killed it, went to start it and it would not turn over, i thought simple enough, the starter relay was bad, i got out and used a screwdriver to start it on the relay., went and bought a new relay and replaced it, still wont turn over, i thought it might be the clutch sensor, changed it, nothing, took apart the dash to get to steering wheel switch tested it, it is fine, is there a fuseable link somewhere im missing, run out of ideas here, driving me crazy. thanks in advance for the help.
#2766 of 2825
Take out my dash by dtheman42
Jun 11, 2009 (8:38 am)
Reply
hey i have a 93 Ford Ranger and i'm trying to take my dash out to repaint it how would i talke it out i can't figure it out.
#2767 of 2825
1996 Ranger XLT 4 cylinder by burnselk
Jun 13, 2009 (7:52 am)
Reply
My "Check Engine" like came on one day and has been on for at least a year now. When this light came on it did not seem to change the way the truck runs nor did it seem to effect in the gas mileage.
 
What could have caused this light to come on and what can I do about it short of taking it to a repair shop? I'd prefer to fix it myself for obvious reasons if at all possible.
 
I like to work on such things myself (to save the trouble and $) and would appreciate hearing back from some of you about this. Thanks a million.
#2768 of 2825
Re: 1996 Ranger XLT 4 cylinder [burnselk] by bolivar
Jun 13, 2009 (10:35 pm)
Reply

Replying to: burnselk (Jun 13, 2009 7:52 am)

Most auto parts houses, Autozone, etc, will read out codes and tell you the general info for the code.
 
They do this in support of selling you parts to fix it.
#2769 of 2825
backfire once warmed up by southtxranger
Jun 16, 2009 (5:18 pm)
Reply
My 2000 2.5L starts good and runs great until it warms up. Once warmed up it begains to backfire and has no power under load. Sometimes if I feather the trottle off the start (standard tranny) it goes away till the RPM's drop. then it goes back to backfiring and running like crap. Changed the fuel filter, helped for a while, then the plugs, no help. Air filter new but cant get her to run right. Any ideas?.......Jim
#2770 of 2825
broken manual lock by brillopad27
Jun 22, 2009 (9:31 am)
Reply
Hi,
I can not lock/unlock my passenger side car door with a key anymore. I opened up the door panel and found that the lock tumbler was not attached to anything and a long metal piece with a plastic and metal clip attached to it fell down. What I need to know is how to reinstall the metal piece so that I can lock/unlock my door from the outside again?
 
Thanks!
#2771 of 2825
Re: broken manual lock [brillopad27] by burnselk
Jun 22, 2009 (11:00 am)
Reply

Replying to: brillopad27 (Jun 22, 2009 9:31 am)

Your best bet would be to stop by your local Ford dealer and talk to the "Parts Department". They can look it up on their computer and show you a picture of what you need and tell you how to do it. They can also sell you the parts you may need. Good luck on that. My drivers side lock is giving me trouble.....takes me a couple of minutes to get it unlocked.....people think I'm trying to steal my own truck....I have to wiggle and jiggle the key just right to get it unlocked.
#2772 of 2825
Re: broken manual lock [brillopad27] by bolivar
Jun 22, 2009 (9:06 pm)
Reply

Replying to: brillopad27 (Jun 22, 2009 9:31 am)

Open up the door on the other side and look at the linkage there. It should be a mirror image.
 
It probably just came loose, or the clip on the end broke.

Messages Page 278 of 284
1
...
275
276
277
278
279
280
281
...
284
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics

Today's Chats

Advertisement