You are here: Forums Pickups Ford Ranger Ford Ranger Maintenance and Repair

Ford Ranger Maintenance and Repair

2825 messages,  Last post on Nov 27, 2009 at 6:47 PM

You are in the Ford Ranger Forum. Your Host is kcram

What is this discussion about? Ford Ranger, Truck

Messages Page 273 of 284 1 ... 270 271 272 273 274 275 276 ... 284 Prev Next Last

Go To Msg # Search This Discussion

#2712 of 2825 Re: Turn signals not working [jherr] by wookie1 Jul 29, 2008 (7:27 am)
Replying to: jherr (Jul 28, 2008 4:49 pm) your flasher unit will also cause the turn signals to stop working. i would say thats what the problem is. hope this helps!
#2713 of 2825 Re: Turn signals not working [jherr] by nvbanker Jul 29, 2008 (9:29 am)
Replying to: jherr (Jul 28, 2008 4:49 pm) Yes, and your flasher unit is usually attached to the fuse panel, a quarter sized round aluminum plug in unit. Find and replace that, and you are probably back in business.
#2714 of 2825 98 Ranger elecrical problem by cryintime Aug 03, 2008 (2:25 am)
the speedometer,wipers,domelight all quit at the same time,they work when the key is in the on or acc position but will not work when truck is running.When I unplugged the RABS sensor on the differential they would not work at all so i replaced that sensor but still they dont work when truck is running. Its a 1998 ranger 2wheel drive manual trans 4 cyl please help
#2715 of 2825 Re: 2004 transmission fluid [bolivar] by robtlnj97 Aug 03, 2008 (4:58 am)
Replying to: bolivar (Jul 22, 2008 11:22 am) I know my '04 Ranger uses Mercon V, DO NOT MIX Mercon with Mercon V. There is no cabin filter in these vehicles.
#2716 of 2825 parking brake adjustment by gsimms81 Aug 18, 2008 (12:33 pm)
I put new brake shoes in a 1998 ford ranger splash and I noticed the rear pass. side shoes were worn on the tops...The parking brake cable is too short and is putting pressure on the top of the shoes where the linkage fits into the brake shoe. Is there an adjustment on the parking brake cable? Replies to this message: gasgas321 (Aug 29, 2008 6:13 am)
#2717 of 2825 Need to replace a catalytic converter by rangernoob Aug 26, 2008 (1:29 pm)
I have a '98, 2.5L, with a hole in my catalytic converter. If I decide to replace rather than repair, is that something a novice can do ?   Also, I have been looking for good references or a step-by-step guide, but am having trouble finding easy to understand information suitable for a mechanic like myself. Anyone have a good suggestion?
#2718 of 2825 Re: parking brake adjustment [gsimms81] by gasgas321 Aug 29, 2008 (6:13 am)
Replying to: gsimms81 (Aug 18, 2008 12:33 pm) DON'T QUOTE ME ON THIS, BECAUSE I HAVEN'T HAD TO ADJUST ANY RANGER PARKING BRAKES, BUT ALL OTHER VEHICLES I HAVE HAD TO ADJUST ARE USUALLY AT, OR NEAR THE ACTUAL LEVER.. I.E. THE EMERGENCY BRAKE HANDLE IN A CAR OR THE FOOT PEDALS IN THE RANGERS...
#2719 of 2825 I NEED A HARMONIC BALANCER!! by jamccurrie Aug 29, 2008 (12:04 pm)
I have been looking for a harmonic balancer for 92 ford ranger with a 2.3 l, 4 cylinder. I have tried every resource I have. Everyone is out of stock. New or used, i dont care. Can anyone help? Replies to this message: wookie1 (Sep 19, 2008 2:29 am)
#2720 of 2825 Where is the "split yoke" located on my driveline? by drewglenn04 Sep 18, 2008 (7:48 pm)
I have the thump/clunk problem when stopping and taking off. I read a thread about drilling a 7/32 hole into my split yoke near the front u-joint and then installing a 1/4" grease fitting so I can grease the spline yoke....would this be the yoke between the rear end and the u-joint back the furthest?   Here's what I read:   "Please post this everywhere you can. Here is the solution and it doesn't invlove driveshaft replacement or removal. Drill a 7/32 hole in your split yoke close to your front u-joint(so you don't drill into your splines). Purchase a 1/4x28 grease fitting 1/4x28 tap. Install grease fitting and inject heavy duty grease into your driveshaft. This will coat your splines. Do not overfill or you will rupture your boot that covers your 2 piece connection. Easy to do and if driveline slop comes back, get the grease gun out and recoat in minutes. Worked great on my 2000 extended cab."
#2721 of 2825 Re: I NEED A HARMONIC BALANCER!! [jamccurrie] by wookie1 Sep 19, 2008 (2:29 am)
Replying to: jamccurrie (Aug 29, 2008 12:04 pm) i used to have one for a 93 ranger 2.3 don't know if i still have it or not. i will look through my parts and see i kept a few things my email is starcar33yahoo.com i live in Ruskin,Florida

Messages Page 273 of 284 1 ... 270 271 272 273 274 275 276 ... 284 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Pickups Ford Ranger Ford Ranger Maintenance and Repair