You are here: Forums Pickups Ford Ranger Ford Ranger Maintenance and Repair

Ford Ranger Maintenance and Repair

2716 messages,  Last post on Aug 18, 2008 at 1:33 PM

You are in the Ford Ranger Forum. Your Host is kcram

What is this discussion about? Ford Ranger, Truck

Messages Page 187 of 272 1 ... 184 185 186 187 188 189 190 ... 272 Prev Next Last

Go To Msg # Search This Discussion

#1857 of 2716 Re: 1997 Ford Ranger position of Air Control only on defrost [branj_jose] by cwerman Dec 13, 2005 (8:26 pm)
Replying to: branj_jose (Dec 11, 2005 11:25 pm) My 1999 Ranger has the same problem with the air control stuck on defrost. I am just starting to research the problem. I will let you know if I figure it out. Any help or suggestions would be great. Replies to this message: bolivar (Dec 14, 2005 12:46 am)
#1858 of 2716 Re: 1997 Ford Ranger position of Air Control only on defrost [cwerman] by bolivar Dec 14, 2005 (12:46 am)
Replying to: cwerman (Dec 13, 2005 8:26 pm) I think this is the year (or a couple of years about this age) with a 'usual' problem.   I can't describe exactly the problem, with correct names, but here is my best try.   The post on one of the 'air control' flappers (or the post on the control rod that moves the flapper) in the heater box is broken. It is plastic, and it just breaks. To repair, the dash must be removed to get it out. And the part (I think) is part of the entire air control set of flappers ( usually 2 or 3 'flappers') - it must all be replaced. Big money. $1,000 or so.   If you are mechanically handy, if you look on other Ford Ranger sites, there is a documented 'work around'. It is pretty messy, involving drilling a hole through the broken shaft and inserting a pin, or something like this. Not really sure about this. But it fixes the old part and don't have to buy the entire air assembly.   Good luck. If this is your problem, you have quite a problem to get it working correctly again.
#1859 of 2716 Re: Engine Failure [lonewulf] by mcs2 Dec 14, 2005 (5:46 pm)
Replying to: lonewulf (May 12, 2001 9:06 pm) have a 2000 ranger. engine blew 38000mi. all internall (no oil or visual damage). same loss of compressoin and loss of all electric power as well. dealer blamed valve spring break, had to replace engine. i am hearing more of this prob. and wonder about manufacturing prob. there is a reason for loss of compression...
#1860 of 2716 Re: Rear brakes freezing [delyla312] by mrp1 Dec 16, 2005 (8:41 am)
Replying to: delyla312 (Dec 05, 2005 12:46 pm) Hi,   I had the exact same problem with my 99. They would usually break free but the last time resulted in a trip to the shop on a flatbed. The problem is a seal on the rear hub that is prone to leaking. The folks at Utton's Mufflers (802) 229-9005 in Montpelier Vt are familiar with the issue and can tell you exactly what the problem is.   Good luck.   MP
#1861 of 2716 Re: 4wd drops out and ABS fails on 1999 Ranger XLT [ar15203] by mrp1 Dec 16, 2005 (8:58 am)
Replying to: ar15203 (Dec 12, 2005 1:46 pm) Visually erfiy that your front drive shaft still spins (drive back and forth a few times) after the 4wd drops out. If so, its either bad locking hubs (I had to replace mine) or a vacuum leak on the lines that drive the locking hubs (also a problem on mine). The lines come off the front hubs and meet just in back of and below the right headlight at a solonoid then run back to the firewall. put a vaccum gauge on the line at the hubs and verify that it pull 14 in of h20 vacuum and doesn't leak more than .5 in h20 in 30 seconds. repeat for both hubs and then upstream of the vacuum solonoid.   Good luck,   MP
#1862 of 2716 Re: 1988 Ranger clutch [wfj1998] by billybob6 Dec 16, 2005 (4:40 pm)
Replying to: wfj1998 (Nov 27, 2005 7:07 pm) Yes, I have 87' 2.9 5 speed. The clutch was just replaced and the point of friction is so far off the floor it is almost at the point where the pedal stops. It is hard to drive, but you just have to get used to it.
#1863 of 2716 93 ranger - screeching at startup by ejr16 Dec 17, 2005 (3:09 pm)
I've got a 93 Ranger V6 5-speed, and about a month ago, it has started to make a clacking/screeching right at cold startup. It goes away after started, and does not happen if it has been started multiple times and warms up.   Any ideas?? Replies to this message: brysue (Dec 26, 2005 10:47 am)
#1864 of 2716 2002 Ford Ranger Egde by lnoirot Dec 17, 2005 (5:01 pm)
How do I disable the anti theft device so my auto starter will work, I have a transponder in it now with the code key in it, but when I plug in the power to the bulldog starter, the parking lights blink continuosly Iv tryed a few things already but nothing seems to work, can any one help, thank you Louis
#1865 of 2716 LOSING SPEED GOING DOWNHILL by brently1 Dec 18, 2005 (11:36 am)
I have a 2000 Ranger 4.0L V6 automatic. I am having a problem. When I go downhill, i lose speed like no tomorrow, out of all vehicles I have driven I have never had a problem losing speed downhill. I have checked my brakes and they are fine, nothing has rusted up. Is it possibley my transmission not going out of a gear it should be? and is it a sensor or a solenoid I can replace. any help would be greatly appreciated.
#1866 of 2716 Noise from my power steering by brently1 Dec 18, 2005 (12:01 pm)
My truck has quite a noise coming from the power steering. Is this normal for the rangers? Replies to this message: redsoxfan5 (Dec 23, 2005 3:13 am) cdduv (Jan 09, 2006 3:14 pm)

Messages Page 187 of 272 1 ... 184 185 186 187 188 189 190 ... 272 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Pickups Ford Ranger Ford Ranger Maintenance and Repair