You are here: Forums Pickups Chevrolet S-10 & GMC S15 Sonoma Chevy S10/GMC S15-Sonoma: Problems & Solutions 

Chevy S10/GMC S15-Sonoma: Problems & Solutions - READ ONLY

2018 messages,  Last post on Oct 17, 2006 at 9:12 PM

You are in the Chevrolet S-10 & GMC S15 Sonoma Forum. Your Host is kcram

What is this discussion about? Chevrolet S-10, GMC Sonoma, GMC S-15, Truck

Messages Page 63 of 203 1 ... 60 61 62 63 64 65 66 ... 203 Prev Next Last

Go To Msg # Search This Discussion

#617 of 2018 Manual Transmission by airpowr Apr 07, 2005 (12:40 pm)
I just purchased a 1996 GMC Sonoma 4.3L with m/transmission. It shifts fine, and everything seems okay, but it makes clicking and clanking noises when you shift gears. Besides the noise it shifts fine, the clutch feels normal also. Are these noises normal for these trucks? I haven't owned a GMC before, so I don't know.   JP
#618 of 2018 Re: Floor Vent [airpowr] by joe3891 Apr 07, 2005 (2:04 pm)
Replying to: airpowr (Apr 07, 2005 12:31 pm) My 99 will flow air out the floor vent with everything off, it flows hot air in the summer. I complained to the dealer under warranty and was told they all do it. I made them take me out in a new one and it did the same thing, they said when hot air comes out in the summer turn it on vent and modulate it, if its still to hot told me to use my a/c, great uh. Its a 2.2 l, great milage at $2.20 a gallon.
#619 of 2018 Re: 97 S10 Vortech V6 lost power & died [geo13] by diver80 Apr 07, 2005 (4:45 pm)
Replying to: geo13 (Apr 06, 2005 11:50 am) i had a problem similar to that and it was my oil pump
#620 of 2018 ecm comptuer by diver80 Apr 07, 2005 (4:51 pm)
does anyone know what code reader to use on a 95 sonoma 2.2, it has an OBD2 hook up but it runs on a OBD1 computer.
#621 of 2018 95 s10 computer by diver80 Apr 07, 2005 (4:17 pm)
i have a 95 s10 2.2 with a little more then 120k on it. does anyone know what code reader it is to retrieve the trouble codes from the ecm....GM switched the hook up for the computer from an OBD1 to an OBD2 but left the computer as a 1 ... im tring to find out why the motor hesitates when you take your foot off the gas Replies to this message: joe3891 (Apr 08, 2005 9:26 am) diver80 (Apr 10, 2005 12:38 am) joe3891 (Apr 11, 2005 9:27 am)
#622 of 2018 still looking for help by lingren Apr 07, 2005 (10:21 pm)
still looking for help to #610 above. 1989 s10 2.5 4cyl thanks Replies to this message: canufixit (Apr 08, 2005 6:10 am)
#623 of 2018 Re: still looking for help [lingren] by canufixit Apr 08, 2005 (6:10 am)
Replying to: lingren (Apr 07, 2005 10:21 pm) HI,   A few comments - Not sure if this helps ...   Sounds like you are not getting fuel ... another reply suggested the in engine compartment, change the Fuel Filter ... If you can - while you have the line open (and BE CAREFUL HERE due to the line pressure) see if you can turn on the fuel pump and verify you actual have good flow - and check the pressure as well ... It may be that crap and corrosion from the tank (from sitting or may be someone dumped in some foreign matter ??) clogged the fuel filter under the hood (and the injectors). Also, I'm not sure , but there may? be a fuel filter in the tank ?? Again, lack of flow / pressure may indicate that this filer (if there?) is blocked as well.... IT really sounds like a fuel supply problem .... Maybe even the fuel pump??
#624 of 2018 Re: 1997 2wd S-10 Split Driveshaft [redtruck] by canufixit Apr 08, 2005 (6:14 am)
Replying to: redtruck (Apr 06, 2005 6:10 am) Just a thought .... Does this squeak/make noise ALL the time when you move off a dead stop - or only after you first stop, then go ?? If it's only after you apply the brakes and stop first - the rear end may be "Twisting" / torquing (along the wheel axis) whn you stop - then when you start up - the rear end "un twists" and squeaks due to the movement in the rubber attachment bushings ... Replies to this message: redtruck (Apr 18, 2005 12:41 pm)
#625 of 2018 Re: 95 s10 computer [diver80] by joe3891 Apr 08, 2005 (9:26 am)
Replying to: diver80 (Apr 07, 2005 4:17 pm) What I understand is the computer is read with OBD 1 scanner and you have to use a special cable. For 1994-1995 GM OBD-1 vehicles with a 16 pin connector uses a blue connector, so my AutoXray Manual states. Replies to this message: diver80 (Apr 10, 2005 12:38 am) joe3891 (Apr 11, 2005 9:27 am)
#626 of 2018 2003 S-10 computer by gordonrules Apr 08, 2005 (12:01 pm)
I have a 2003 S-10 Crew Cab and the Check Engine Light just came on for the first time. Does anyone know how and where to read the codes on the computer so I can figure out what is wrong? I know this is easy, as I have done it on previous vehicles, it's just that I haven't had to on this truck and I can't find a website that will tell me. If anyone knows of a website where I can find this that would be great. Thanks in advance. Replies to this message: alcan (Apr 09, 2005 2:33 am) ryno (Apr 12, 2005 4:15 pm)

Messages Page 63 of 203 1 ... 60 61 62 63 64 65 66 ... 203 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Pickups Chevrolet S-10 & GMC S15 Sonoma Chevy S10/GMC S15-Sonoma: Problems & Solutions