Last post on Oct 17, 2006 at 8:12 PM
You are in the Chevrolet S-10 & GMC S15 Sonoma
What is this discussion about?
Chevrolet S-10, GMC Sonoma, GMC S-15, Truck
#1050 of 2018 2001 chevy s-10 2.2
Sep 02, 2005 (4:15 am)
i need some help i have a 2001 s-10 2.2 and i need some adivce does any one out there know why or maybe it is just my tuck but this thing dont have enough power to get out of its own way it seems like it is in second gear when it takes off very slow truck another thing is sometimes when i turn the blinker on a bell sounds like the door is open or some thing also the gas gauge is off. this truck is a nice looking truck and only has about 36000.on it should i have these problems?
#1051 of 2018 Re: 2001 chevy s-10 2.2 [ricky24]
Sep 02, 2005 (8:43 am)
I would say it is starting off in 2nd, any codes.
#1052 of 2018 2001 S-10 service engine light problem
Sep 03, 2005 (10:17 am)
I have a 2001 S-10 with a 4.3 engine. My service engine light is on with a code of 1345. In the book that code means cam shaft to crank shaft position correlation is faulty I want to know what that means. If it's a sensor I have to replace or what it means.
#1053 of 2018 87 S10 4x4, 4 speed manual - 5 speed manual
Sep 03, 2005 (11:24 am)
I have a 5 speed out of a 2 wheel drive s10. I would like to to remove my (4x4) 4 speed transmission and install the 5 speed.
OTHER THAN CHANGING OUTPUT HOUSING, will the output shaft from my 4 speed interchange with the 5 speed's guts?
#1054 of 2018 1993 S-10 4.3 v-6 4x4
Sep 03, 2005 (6:05 pm)
Today went 4x4 and went through a 4 foot deep mudd hole, well it started getting very hard to keep alive when they were towning it out so I was told to cut it so water would not enter the engin, so I did! Wel after I was out it would not start for 30 min. Then it started to crank, but would not egnite! So I was pulled to a long hill and we did a rolling start! Well now it starts fine, but when I shif it in to gears nuttin happend the rpms go up butn the truck does not move! Any sussgestions?
#1055 of 2018 Re: 2001 chevy s-10 2.2 [ricky24]
Sep 04, 2005 (11:25 am)
I specialize in wiring problems, and the only thing that fits your problem is a loose
connecter in the back of your instrument cluster " Gauge Pod". Your transmission shifts gears based on a signal from the "vehicle speed sensor". This sensor is also used to turn the Seedometer. If you have a bad connection to the instrument
cluster, or damage to that connection, if will cause your gas gauge not to work, your truck not to sift right, turn signal problems, etc. Any curcuit that runs through the printed curcuit on the back of the "cluster". Usually, the connectors are just misaligned in there sockets.
This could also be caused by a loose ground to the cluster, check your main dash ground located in the lower left corner of the dash, above the E-brake, 14 or 16 gauge black wire.
That should get you fixed-up!
#1056 of 2018 Re: 2001 S-10 service engine light problem [cowtowngirl]
Sep 04, 2005 (12:41 pm)
You are correct, More than likely, it is a faulty crank sensor, mounted above the main pully at the front, bottom of the engine. Your camshaft sensor is mounted behind the water pump on the front of the motor, or is build into the distributer, depending on year model. Basiclly, it you have a Distributer, the camshaft sensor is in it "pickup coil" Recommend that you have your car tested with a DIAG computer. This will show the values for each sensor in real time, and pen point the
problem. I would not recommend buying parts, as this could even be a damaged ECM. The factory service manual from a dealer will tell you step by step tests for each part, including the wiring harness.
#1057 of 2018 1999 S10 problems after some time of running ...
Sep 05, 2005 (2:34 pm)
I just bought a 1999 Chevy S10 pick up, 5 speed 2.2L. Everything seems ok but the only problem is that after running for a while, when i make a stop, and try to shift to 1st, the engine will stop or it will start jumping like when you take out the clutch out and don't put enough gas on the engine, then if i put it in to neutral, at low rpm the engine sounds good but ass soon as i push the gas, the engine starts jumping and coghing like if it had an obstructed fuel line. I already change the fuel filter, and the air filter, and a mechanic check the fuel pump presure and checks ok, and the comspumtion of fuel seems ok. The mechanic got some codes from the car's diagnostic module, didn't told me which ones, but just told me one was from the TPM and another from some some part of the chassis.
I don't think is an obstructed fuel line because the problem seems to be very random and it's not using too much fuel nor lack power of anything when its running good. Then if i turn off the engine for 1hr or more, then it starts just like new. Any ideas how to find out what it is? I hope i can find out what it is, because i'm about to sell the damn thing. Thanks
#1058 of 2018 Re: 1999 S10 problems after some time of running ... [tjdude]
Sep 06, 2005 (5:54 am)
Just a thought ... maybe you have two problems ?? 1 is the rough running and the second is the clutch itself?? When you put in in gear with the clutch in - it should not change the engine speed - providing - the clutch is really adjusted correctly. Perhaps the clutch needs adjustment as it is still slightly rubbing on the flywheel when the clutch is in ???
Sep 06, 2005 (6:43 am)
A 96 S10 4x4 5 speed- whats the best weight synthetic oil for the gearbox? It says gm synchromesh oil, but what the hell is that? I'd rather have synthetic oil in it. I put in 90 w gear oil and now it grinds when shifting cold. Any suggestions on what weight to use ??