You are here: Forums Sedans Nissan Maxima Nissan Maxima Maintenance and Repair

Nissan Maxima Maintenance and Repair

4048 messages,  Last post on Nov 23, 2009 at 4:23 PM

You are in the Nissan Maxima Forum. Your Hosts are pat & karens

What is this discussion about? Nissan Maxima, Sedan

Messages Page 392 of 405 1 ... 389 390 391 392 393 394 395 ... 405 Prev Next Last

Go To Msg # Search This Discussion

#3910 of 4048 Re: Nissan Maxima Stalling [galka5] by obyone Oct 01, 2008 (12:12 pm)
Replying to: galka5 (Oct 01, 2008 7:34 am) It's either the mass air flow sensor or the throttle position sensor. Replies to this message: galka5 (Oct 01, 2008 12:20 pm)
#3911 of 4048 Re: Nissan Maxima Stalling [obyone] by galka5 Oct 01, 2008 (12:20 pm)
Replying to: obyone (Oct 01, 2008 12:12 pm) Thank you so much
#3912 of 4048 Re: 03 maxima check engine light [mopardude360] by jorghi Oct 04, 2008 (4:01 pm)
Replying to: mopardude360 (Apr 26, 2008 3:15 pm) Not to worry. After a spark plug replacement, you will get codes because you disconnected a bunch of wires. Just reset the codes ( or have them reset at a place like AutoZone) . In a couple of weeks the engine computer will collect enough data and you can pass inspection etc.. will be A-Ok.
#3913 of 4048 Re: My Car Won't Start!! [kanej316] by jorghi Oct 04, 2008 (4:03 pm)
Replying to: kanej316 (May 02, 2008 12:23 pm) If this is a stick shift, make sure you are pushing the clutch pedal all the way down.
#3914 of 4048 98 maxima-inspection-3 fault codes by ashmax Oct 05, 2008 (8:52 pm)
I took my maxima in for an inspection and it did not pass due to the service engine light being on. The mechanic said 3 fault codes popped up which were: P0110, P0325, and P0100.  A friend said my O2 sensor might need to be changed and it would correct all those codes.  If anyone knows anything further on this and know how much $$$ this might end up costing me please give me some input!   Thank you! Replies to this message: obyone (Oct 06, 2008 2:22 am) Mr_Shiftright (Oct 06, 2008 6:47 am)
#3915 of 4048 Re: 98 maxima-inspection-3 fault codes [ashmax] by obyone Oct 06, 2008 (2:22 am)
Replying to: ashmax (Oct 05, 2008 8:52 pm) P0325 Knock Sensor 1 Circuit Malfunction (Bank I or Single Sensor) P0100 Mass or Volume Air Flow Circuit Malfunction P0110 IAT Circuit Malfunction   You need to replace a knock sensor on bank 1, MAF, Intake Air Temperature is usually a function of the MAF so I'd replace the MAF and check it from there.   BTW, I don't see anything relating to the O sensors. So how did your friend figure this out? Replies to this message: Mr_Shiftright (Oct 06, 2008 6:47 am)
#3916 of 4048 Re: 98 maxima-inspection-3 fault codes [obyone] by Mr_Shiftright HOST Oct 06, 2008 (6:47 am)
Replying to: obyone (Oct 06, 2008 2:22 am) computer codes don't identify the defective component. All they can do is tell you the system, circuit or component that is currently unhappy. As to WHY it's unhappy, that requires further hands-on diagnostics. The MAF can be tested and that's an excellent place to start.
#3917 of 4048 99 maxima stalling by 99max2 Oct 08, 2008 (12:02 pm)
I have a 99 maxima, its been a great vehicle for its 240k. after the 1st 100k i made the stalling go away with O2, plugs, coils, mass air flow being replaced, even at 190 when it returned i replaced O2 plugs, coil and mass air flow. but it isnt going away. for a day it will run fine then slowly start back. It boggs down when first taking off. Then as it warms up it becomes more pronounced. Soon even when running at higher speeds the RPMs drop. At this point it wont idle in park and can become very hard to start again. I never have replaced the Idle air control valve. Thats my next step. any other sugestions ? I dont wont to get rid of it. The engine and transmission and appearance are stll very good. But when after bringing it to Nissan and they could not ID it I am very discouraged. Replies to this message: obyone (Oct 08, 2008 2:31 pm) 99max2 (Oct 08, 2008 5:28 pm) rexkay (Oct 08, 2008 6:37 pm)
#3918 of 4048 Re: 99 maxima stalling [99max2] by obyone Oct 08, 2008 (2:31 pm)
Replying to: 99max2 (Oct 08, 2008 12:02 pm) When was the last time you changed out the catalytic converters? Those will definitely plug after awhile. While you should get a check engine light when they go bad, sometimes you don't. Replies to this message: 99max2 (Oct 08, 2008 5:28 pm)
#3919 of 4048 Re: 99 maxima stalling [obyone] by 99max2 Oct 08, 2008 (5:28 pm)
Replying to: obyone (Oct 08, 2008 2:31 pm) I have not replaced and the dealership has not suggested that on this problem. My emissions inspection passes very well. Maybe it has lasted so long because i only use bp premium. Thank you for your reply and i will check converters too.

Messages Page 392 of 405 1 ... 389 390 391 392 393 394 395 ... 405 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Sedans Nissan Maxima Nissan Maxima Maintenance and Repair