You are here: Forums Sedans Nissan Maxima Nissan Maxima Maintenance and Repair

Nissan Maxima Maintenance and Repair

4048 messages,  Last post on Nov 23, 2009 at 4:23 PM

You are in the Nissan Maxima Forum. Your Hosts are pat & karens

What is this discussion about? Nissan Maxima, Sedan

Messages Page 392 of 406 1 ... 389 390 391 392 393 394 395 ... 406 Prev Next Last

Go To Msg # Search This Discussion

#3907 of 4048 Re: Nissan Maxima Stalling [oceanblue] by galka5 Oct 01, 2008 (7:34 am)
Replying to: oceanblue (Dec 26, 2000 2:16 pm) Oceanblue, I think i have the same problem with my Maxima ' 97. After stopping on a traffic light, when light changes to green and I take my foot from the brake and put it on gas the car either shuts down or it feels like it doesn’t want to go on the first gear, no matter how hard I push the pedal. If it shuts down, it usually restarts in about 20 seconds. It happens few times a day, not all the time. Mechanics are unable to determine the problem and i already spent $500 on same things you did. Don't know what to do anymore. Replies to this message: obyone (Oct 01, 2008 12:12 pm) galka5 (Oct 01, 2008 12:20 pm)
#3908 of 4048 by galka5 Oct 01, 2008 (7:37 am)
I think i have the same problem with my Maxima ' 97. After stopping on a traffic light, when light changes to green and I take my foot from the brake and put it on gas the car either shuts down or it feels like it doesn’t want to go on the first gear, no matter how hard I push the pedal. If it shuts down, it usually restarts in about 20 seconds. It happens few times a day, not all the time. Mechanics are unable to determine the problem and i already spent $500 on same things you did. Don't know what to do anymore. Replies to this message: smith_gw (Oct 01, 2008 9:03 am)
#3909 of 4048 Re: [galka5] by smith_gw Oct 01, 2008 (9:03 am)
Replying to: galka5 (Oct 01, 2008 7:37 am) I had a similar problem with my 98 SE. When accelerating from a stop position, the car would jerk and not want to go. It was almost the same feeling as if the clutch was let out too fast on a manual transmission. My car was diagnosed by our mechanic as needing a new mass air flow sensor. This was replaced (total cost was around $450-$500) and the issue hasn't occurred since.   Good luck.
#3910 of 4048 Re: Nissan Maxima Stalling [galka5] by obyone Oct 01, 2008 (12:12 pm)
Replying to: galka5 (Oct 01, 2008 7:34 am) It's either the mass air flow sensor or the throttle position sensor. Replies to this message: galka5 (Oct 01, 2008 12:20 pm)
#3911 of 4048 Re: Nissan Maxima Stalling [obyone] by galka5 Oct 01, 2008 (12:20 pm)
Replying to: obyone (Oct 01, 2008 12:12 pm) Thank you so much
#3912 of 4048 Re: 03 maxima check engine light [mopardude360] by jorghi Oct 04, 2008 (4:01 pm)
Replying to: mopardude360 (Apr 26, 2008 3:15 pm) Not to worry. After a spark plug replacement, you will get codes because you disconnected a bunch of wires. Just reset the codes ( or have them reset at a place like AutoZone) . In a couple of weeks the engine computer will collect enough data and you can pass inspection etc.. will be A-Ok.
#3913 of 4048 Re: My Car Won't Start!! [kanej316] by jorghi Oct 04, 2008 (4:03 pm)
Replying to: kanej316 (May 02, 2008 12:23 pm) If this is a stick shift, make sure you are pushing the clutch pedal all the way down.
#3914 of 4048 98 maxima-inspection-3 fault codes by ashmax Oct 05, 2008 (8:52 pm)
I took my maxima in for an inspection and it did not pass due to the service engine light being on. The mechanic said 3 fault codes popped up which were: P0110, P0325, and P0100.  A friend said my O2 sensor might need to be changed and it would correct all those codes.  If anyone knows anything further on this and know how much $$$ this might end up costing me please give me some input!   Thank you! Replies to this message: obyone (Oct 06, 2008 2:22 am) Mr_Shiftright (Oct 06, 2008 6:47 am)
#3915 of 4048 Re: 98 maxima-inspection-3 fault codes [ashmax] by obyone Oct 06, 2008 (2:22 am)
Replying to: ashmax (Oct 05, 2008 8:52 pm) P0325 Knock Sensor 1 Circuit Malfunction (Bank I or Single Sensor) P0100 Mass or Volume Air Flow Circuit Malfunction P0110 IAT Circuit Malfunction   You need to replace a knock sensor on bank 1, MAF, Intake Air Temperature is usually a function of the MAF so I'd replace the MAF and check it from there.   BTW, I don't see anything relating to the O sensors. So how did your friend figure this out? Replies to this message: Mr_Shiftright (Oct 06, 2008 6:47 am)
#3916 of 4048 Re: 98 maxima-inspection-3 fault codes [obyone] by Mr_Shiftright HOST Oct 06, 2008 (6:47 am)
Replying to: obyone (Oct 06, 2008 2:22 am) computer codes don't identify the defective component. All they can do is tell you the system, circuit or component that is currently unhappy. As to WHY it's unhappy, that requires further hands-on diagnostics. The MAF can be tested and that's an excellent place to start.

Messages Page 392 of 406 1 ... 389 390 391 392 393 394 395 ... 406 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Sedans Nissan Maxima Nissan Maxima Maintenance and Repair