You are here: Forums Sedans Nissan Maxima Nissan Maxima Maintenance and Repair

Nissan Maxima Maintenance and Repair

4048 messages,  Last post on Nov 23, 2009 at 4:23 PM

You are in the Nissan Maxima Forum. Your Hosts are pat & karens

What is this discussion about? Nissan Maxima, Sedan

Messages Page 384 of 405 1 ... 381 382 383 384 385 386 387 ... 405 Prev Next Last

Go To Msg # Search This Discussion

#3829 of 4048 FAULTY WIRING ON SPEED SENSOR by dgm1974 Mar 17, 2008 (1:03 am)
ON MY 1991 NISSAN MAXIMA, I FOUND OUT THAT THE PROBLEM WHY MY SPEEDOMETER & ODOMETER ARE NOT WORKING ,IS THERE IS A FAULTY WIRING OR DISCONNECTED WIRE TO THE SPEED SENSOR. WHAT I DID WAS CONNECTED & SOLDERED THE WIRE. NOW IT IS WORKING. THANKS FOR THE ADVICES..
#3830 of 4048 Re: 03 Maxima idle increase after changing plugs [obyone] by tb4me Mar 18, 2008 (8:32 am)
Replying to: obyone (Mar 16, 2008 10:41 am) thanks--will try that.
#3831 of 4048 Re: Rear Brake ERT [fg54] by Mr_Shiftright HOST Mar 19, 2008 (8:34 am)
Replying to: fg54 (Mar 15, 2008 4:25 pm) what year maxima?
#3832 of 4048 Re: 1991 nissan maxima speed sensor? [dgm1974] by daub Apr 04, 2008 (2:20 am)
Replying to: dgm1974 (Mar 05, 2008 10:10 pm) Just had the identical problem with my son in laws Stratus. Auto Zone said it was the "output speed sendor on the transmission". Went to the dealer for the part. $20.00. Found where it was located and replaced. Works great. The speedometer not working is a clear sign. Make sure you replace the "output" sensor as there is an input that looks similar.
#3833 of 4048 '02 Maxima P0138 Error Code by ldc5 Apr 04, 2008 (4:58 pm)
The check engine light started coming on about 9 months after buying my '02 Maxima, with the P0138 code. Although it only has ~78K miles on it, I replaced the O2 sensor recommended by the error code diagnosis and cleared the error code using an Actron analyzer. The same code still comes on......any advice to finally resolve putting-out this darn check engine light is greatly appreciated.   Dennis Replies to this message: Mr_Shiftright (Apr 04, 2008 6:14 pm) obyone (Apr 04, 2008 10:09 pm) ldc5 (Apr 05, 2008 3:43 am) ldc5 (May 02, 2007 9:38 am) Mr_Shiftright (Apr 05, 2008 4:54 pm) and 1 more... ldc5 (Apr 09, 2008 4:49 am) Mr_Shiftright (Apr 09, 2008 9:06 am) and 3 more...
#3834 of 4048 Re: '02 Maxima P0138 Error Code [ldc5] by Mr_Shiftright HOST Apr 04, 2008 (6:14 pm)
Replying to: ldc5 (Apr 04, 2008 4:58 pm) You might need to have the harness checked for bad wiring. This can cause the ECM to get a weird voltage signal from the 02 sensor 2, and throw the P0138 code.   So maybe clean up whatever connections you can and clear the code. It might clear itself. Sometimes they do. Replies to this message: obyone (Apr 04, 2008 10:09 pm) ldc5 (Apr 05, 2008 3:43 am) ldc5 (May 02, 2007 9:38 am) Mr_Shiftright (Apr 05, 2008 4:54 pm) obyone (Apr 05, 2008 5:12 pm) ldc5 (Apr 09, 2008 4:49 am) Mr_Shiftright (Apr 09, 2008 9:06 am) challatt7 (Apr 23, 2008 3:14 pm) and 2 more...
#3835 of 4048 Re: '02 Maxima P0138 Error Code [Mr_Shiftright] by obyone Apr 04, 2008 (10:09 pm)
Replying to: Mr_Shiftright (Apr 04, 2008 6:14 pm) I had a similar problem once. Replaced the O2 sensor, cleared the check engine light, after running a couple of minutes the check engine light returns. Code says MAF then I'm thinking man this sucks and yank the battery cable and left it off for 30 minutes. Reconnect and all codes cleared and never came back.   Sometimes a hard reboot will do it. Replies to this message: ldc5 (Apr 05, 2008 3:43 am)
#3836 of 4048 Re: '02 Maxima P0138 Error Code [Mr_Shiftright] by ldc5 Apr 05, 2008 (3:41 am)
Replying to: Mr_Shiftright (Apr 04, 2008 6:14 pm) Thank you. I assume you mean the harnes & connector leading from each oxygen sensor all the back to the ECM?....another question, do you have an opinion on if Haynes manual for this car has sufficient detail, or should I invest in the shop manual? Replies to this message: Mr_Shiftright (Apr 05, 2008 4:54 pm) obyone (Apr 05, 2008 5:12 pm)
#3837 of 4048 Re: '02 Maxima P0138 Error Code [obyone] by ldc5 Apr 05, 2008 (3:43 am)
Replying to: obyone (Apr 04, 2008 10:09 pm) Thanks will try this first, before ripping into checking continuity along the harness
#3838 of 4048 Re: '02 Maxima P0138 Error Code [ldc5] by Mr_Shiftright HOST Apr 05, 2008 (4:54 pm)
Replying to: ldc5 (May 02, 2007 9:38 am) No Haynes won't do it. Replies to this message: obyone (Apr 05, 2008 5:12 pm)

Messages Page 384 of 405 1 ... 381 382 383 384 385 386 387 ... 405 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Sedans Nissan Maxima Nissan Maxima Maintenance and Repair