You are here: Forums Sedans Chevrolet (Geo) Prizm Chevrolet (Geo) Prizm

Chevrolet (Geo) Prizm

1322 messages,  Last post on Dec 06, 2009 at 2:12 PM

You are in the Chevrolet (Geo) Prizm Forum. Your Hosts are pat & karens

What is this discussion about? Chevrolet Prizm, Geo Prizm, Sedan

Messages Page 94 of 133 1 ... 91 92 93 94 95 96 97 ... 133 Prev Next Last

Go To Msg # Search This Discussion

#924 of 1322 Re: Sudden stalls! Ouch! [mt700a1] by dougleeknowles Aug 19, 2005 (7:04 am)
Replying to: mt700a1 (Aug 18, 2005 10:21 am) I definitely get the sucking sound when removing the gas cap for a fill-up. I'll try loosening up on it, but I'm pretty sure that when the car stalls, all the electrical stuff goes out with it. I haven't had it happen while driving at night yet, tho, so I'm not positive. I'll try working the battery cables around tonite.   Thanks for the suggestions.
#925 of 1322 Changing Exhaust Manifold. Is it a DYI job? by seasideheights Aug 22, 2005 (8:47 am)
Replying to: pat (Aug 01, 2005 10:57 pm) I have a 2000 prizm & the exhaust manifold needs to be replaced.   Is that a do it yourself job?   It appears it involves taking the heat shield off, unscrewing the old one, putting the new one in with a new manifold gasket, screwing it back in, then screwing the heat shield back on.   It doesn't even look like you need to jack up the car to do it.   Is it something I could do right in the driveway? Replies to this message: glenpointe (Aug 23, 2008 12:03 pm)
#926 of 1322 1995 GEO hard Starting by buelmc Aug 24, 2005 (7:06 am)
1995 Geo Prizm 126,000 miles on it (Just broke in) Every Morning regardless of the outside tempature I have to almost totally depress the gas pedal and then play with it to get it to run. After it is warmed up it runs fine. Acts like it has a Bubble in it. I had the heat sensor replaced last week. Fuel Filter? If so where is that located, Gas Cap? Acts almost like it is vapor locking until it gets warm
#927 of 1322 corolla bumper by chadi Aug 26, 2005 (6:44 am)
does a 93-97 corolla front bomper fit on a 93-97 prizm...i like the design of the corolla one better...and i am wondering if all the bolts and screws line up...and if the dimensions are the same...
#928 of 1322 98 prizm steerin wheel removal by nite Aug 29, 2005 (10:35 am)
my wifes 98 prizm the horn dosent wok... i found the wire up by the steering wheel and when i ground the wire the horn works so i am assuming the problem is the horn button... the question i have how do i take the air bag off with out doing any damage to it so i can get to the horn button...thanks in advance   Danny Replies to this message: mt700a1 (Sep 01, 2005 7:51 am)
#929 of 1322 Re: Lsi or regular Prizm model? [iupui95] by crw7 Aug 29, 2005 (5:52 pm)
Replying to: iupui95 (Aug 13, 2005 2:42 pm) It should say LSI on the car somewhere, I would think. The Geo's I've seen have "Prizm" on one side of the rear, and "LSI" on the opposite corner. The Chevy's say "Prizm LSI" together.
#930 of 1322 Re: 98 prizm steerin wheel removal [nite] by mt700a1 Sep 01, 2005 (7:51 am)
Replying to: nite (Aug 29, 2005 10:35 am) If airbag removal is required to get to the horn switch, you shouldn't attempt it at home. It is probably the most complicated interior equipment in your car, and it takes many hours by professionals to do it right. Shops charge hundreds for the work, and sometimes leave the airbag disconnected to save hours of labor without telling you. You want your airbag to be as reliable as it can be, so pick a reputable shop for the work. I haven't checked my repair manual yet but you should check yours and see if there is a way to get to the horn switch without removing the airbag. You can do your brakes and minor engine work, but airbag is a different beast I am told. M
#931 of 1322 93 Geo Help by lasalp Sep 07, 2005 (9:25 am)
Hi there, im looking into buying a 93 geo prism. But its not running real well at this point.It does belong to a family member, he bought it 2 weeks ago and the car ran fine, 70 on the freeway with no problem at all. Now he decides to wash the car with the hood up and the car not running and now the car is all messed up.. He replaced spark plugs,wires cap and still the same, They hooked something up to it(sorry im not very car intelligent) and they found that the 4th plug was not working or was working very little.. It seems like the car is not really getting enough gas either..misses badley and stalls also...any suggestions? sandy Replies to this message: mt700a1 (Sep 12, 2005 8:10 am)
#932 of 1322 Re: 93 Geo Help [lasalp] by mt700a1 Sep 12, 2005 (8:10 am)
Replying to: lasalp (Sep 07, 2005 9:25 am) Water in the ignition coil? M
#933 of 1322 Re: Cylinder Misfire - 2000 Prizm [rlindeman] by jess7 Sep 12, 2005 (3:30 pm)
Replying to: rlindeman (Jun 26, 2005 8:33 am) Also have a 2000 prism that doesn't run well when first started. Have had it tested by a mechanic, but no solutions found. He did find that the problem stops when the engine heats up to a certain point. Anyone else have any ideas? Replies to this message: mt700a1 (Sep 13, 2005 7:09 am) chemgirl1681 (Sep 15, 2005 7:07 am)

Messages Page 94 of 133 1 ... 91 92 93 94 95 96 97 ... 133 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Sedans Chevrolet (Geo) Prizm Chevrolet (Geo) Prizm