You are here: Forums Sedans Chrysler Concorde Chrysler Concorde

Chrysler Concorde

1243 messages,  Last post on Nov 26, 2009 at 1:03 PM

You are in the Chrysler Concorde Forum. Your Hosts are pat & karens

What is this discussion about? Chrysler Concorde, Sedan

Messages Page 123 of 125 1 ... 119 120 121 122 123 124 125 Prev Next Last

Go To Msg # Search This Discussion

#1213 of 1243 Re: 99 Concorde Cracked Door Handle [neilbj] by rwrogers1 Jul 02, 2008 (5:56 pm)
Replying to: neilbj (Jun 08, 2008 3:59 pm) I have the same issue, but both my driver side and passenger side are broke. Did you ever get a response on this request, did you find where to get these at? Replies to this message: neilbj (Jul 04, 2008 12:34 pm)
#1214 of 1243 Re: 99 Concorde Cracked Door Handle [rwrogers1] by neilbj Jul 04, 2008 (12:34 pm)
Replying to: rwrogers1 (Jul 02, 2008 5:56 pm) My selling dealer was able to get a door handle for the driver's side. It was just starting to crack so I thought I would replace it and the passenger side at the same time. The driver's side handle was grey and did not match the camel colored interior. My dealer could not find one for the passenger side.   Just yesterday (July 3) I tried a different dealer. Within a half an hour he returned my call and had located a passenger side handle from another dealer. It's not the original color; it is a tan color however.   The moral of the story: There are still some handles out there. You just have to start calling dealers. Be prepared to give the parts person the last 9 digits of your VIN.
#1215 of 1243 my car won't start by rchristiansen Jul 07, 2008 (7:11 am)
My car will not start. I turn the key like normal, car makes it's normal noise, but it will not start. Besides the fuel pump, what else could it be? Replies to this message: jspyrz (Aug 16, 2008 7:14 am)
#1216 of 1243 01 concord brake bulbs by sparkyrhett Jul 17, 2008 (10:22 am)
Good eve. I am having a problem finding out how to remove and replace the brake light (in the tail light section) on my 91 Chrysler Concord. Can anyone help me. Thanks in advance. Single lady all thumbs Replies to this message: jayrider (Aug 22, 2008 7:34 am)
#1217 of 1243 Re: my car won't start [rchristiansen] by jspyrz Aug 16, 2008 (7:14 am)
Replying to: rchristiansen (Jul 07, 2008 7:11 am) I just went through the same situation. After replacing the fuel pump and another 600$ on a mechanic, it turned out to be a wire running to the pump to run under the back seat had worn into where it goes through the floor board, check to see if the fuel pump is getting power, if not I would definatly check the wires where they may run through grommets to check for wear
#1218 of 1243 Re: 01 concord brake bulbs [sparkyrhett] by jayrider Aug 22, 2008 (7:34 am)
Replying to: sparkyrhett (Jul 17, 2008 10:22 am) Find a gas station that still does auto repairs and have them change it for you. Some Auto Zones will change bulbs for free if there isn't much to do.
#1219 of 1243 Engine light at 90K by concrdgold01 Sep 06, 2008 (4:39 pm)
The check engine light has illuminated at 90,000 mi on my 2001 Concorde LX, 2.7 V-6. To date the only mechanical failure has been an idler pulley bearing. The car runs fine with the light still on. It has not started to blink yet. One thing, I did smell gas fumes briefly when I turned on the heat (it's cold here in Wichita today). Any ideas?
#1220 of 1243 Where is the road speed sensor? by dmcghin Sep 22, 2008 (11:01 am)
I have a 2000 model 3.2LXI. After returning from holiday The car wold not start. I found that the positive battery terminal clamp had corroded. after cleaning up the clamp the car started fine but now the speedometer/odometer/trip computer and cruse contror are not working.Everything lights up but I get no speed indications and the odometer is not counting up any miles. I suspect that the road speed sensor has failed but have no idea where it is on this car. anyone have an answer or any other suggestions.   thanks   Darren
#1221 of 1243 1998 Chrysler Concorde Engine Rebuild 2.7 liter DOHC V6 by pwilliams5 Sep 26, 2008 (1:32 pm)
OK I'm rebuilding a 2.7 liter V6 in a 1998 Chrysler Concorde LX for my boss. Here's the only issue I'm concerned about for the moment. is re installation of the Crankshaft Damper or pulley it was removed using a 3 jaw puller. but to reinstall a special tool C-4685-C1 is required it says cant justify spending 50 bucks on a tool i'm only going to use once. is there any way to install the crankshaft pulley without this tool??   I'm sure i will have more question that i haven't found but for the moment i really just would like to know if there is another way to install the pulley.     thanks Replies to this message: dom324 (Sep 14, 2009 1:52 pm)
#1222 of 1243 Re: Part number for hose off crankshaft 1995 Concorde? [skedeebs] by trevor91 Oct 10, 2008 (5:09 pm)
Replying to: skedeebs (May 04, 2008 8:49 am) Best bet is go to the local Chrysler dealer & explain to them the part you need, most of the hoses are dealer item only.

Messages Page 123 of 125 1 ... 119 120 121 122 123 124 125 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Sedans Chrysler Concorde Chrysler Concorde