Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
Hatchbacks Chevrolet Metro/Geo Metro Chevrolet/Geo Metro
1692 messages, Last post on Oct 24, 2009 at 5:27 PM
You are in the Chevrolet Metro/Geo Metro Forum. Your Host is pf_flyer
|
|
|---|---|
Could be a number of things: spark (did you change the plugs recently?), catalyzer could be plugged up...
|
|
|
Replying to: pipeman (Oct 31, 2006 7:27 am) Thanks for the ideas and recommendations, I'll have to check the compression when I get a chance and take it from there. Thanks again!! |
|
|
Replying to: vanillalatte (Oct 31, 2006 3:13 pm) What I did - remove the Catal. Converter, cut of the front pipe and I cleaned the converter inside. Removed all "honey nest". Installed back and never have any problem. My OX. sensor work better, no more back pressure, better mpg. Passed emission - easy. Just do not mention about that. Pipeman |
|
|
|
Well.....it's not legal really, we are well aware of that. BUT you get better gas mileage, thus you are more efficient, therefore you pollute less......
|
|
|
Replying to: vanillalatte (Nov 03, 2006 4:18 am) Didn't damage the World. |
|
|
|
|
Replying to: pipeman (Oct 31, 2006 7:27 am) Thanks GeoMetro91
|
|
|
Replying to: geometro91 (Nov 05, 2006 11:18 am) Second. Remove the exhaust manifold. After the exhaust manifold is out - clean very well the opening ( 1/2" dia.) accross the cyl.head. From the exhaust to the egr. Look at the exhuast minifold and you will see small hole running between the "exhaust collectors" 1 - 2 -3. The opening is less than 1/8" dia. Use the transmission fluis to clean the passages. Put the one site of the pipe cleaner to the transm. fliud and insert in every small hole. Must go thru. If is plugged, put more transm. fliud in the openong in leave for 15 min. and try push thru. If will not open the hole, use some sharp wire and push. By gental to nor brake the wire. Also you can use high pressure air to clean the passages. Replace all bolts with studs. Easy to work. Use grade 9 or 10 studs. Open the ehaust manifold inlets abut 45 degree angle , the flow will be easier. Before instaling the studs, retap the thread in the cyl. head with greas. Use copper grease to install the studs in the cyl. head. Any questions, let me know. Pipeman - visit my web www.bacartpipes.com
|
|
|
|
|
Replying to: pipeman (Nov 05, 2006 4:21 pm) No sure what you mean by opening up the inlets on the exhaust manifold. Are you talking about taking a die grinder to the manifold itself? If so how far back should the 45 degree bevel go? Thanks, geometro91
|
|
|
|
|
Replying to: geometro91 (Nov 06, 2006 12:24 pm) Also you can do 45 on cyl. head. How about those small holes in the EGR , you located that? If yo will look inside the exh. ports you will see small "pipe" on the bottom of the runners. Let me know.
|
|
|
|
|
Replying to: m564ag (Oct 30, 2006 5:08 am)
|
|
You are here:
Forums
Hatchbacks Chevrolet Metro/Geo Metro Chevrolet/Geo Metro
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
1997 Geo Metro
2001 Chevrolet Metro
Browse by Board
Browse by Topic
Today's Chats
