Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
Sedans Mazda Protege Mazda Protege Maintenance and Repair
3600 messages, Last post on Nov 28, 2009 at 3:21 PM
You are in the Mazda Protege Forum. Your Hosts are pat & karens
|
Replying to: paramount13 (Jul 21, 2008 9:22 pm) I highly recommend not messing with the throttle body adjustments. If it is dirty or clogged, clean it. If all the hoses and tubes are in good shape, check the IAC valve under the throttle body.
|
|
|
|
|
Replying to: maltb (Jul 22, 2008 9:39 am) Thanks
|
|
|
Replying to: paramount13 (Jul 23, 2008 7:45 pm) |
|
96 Mazda Protege LX 1.5L with 104,000 miles, (past) due for timing belt replacement.  Initially told parts needed were: timing belt tensioner cam seals crank seal valve cover gasket timing idlers water pump Estimate totaled $370 for parts (from Advance, not Mazda parts), $200 labor - this all by a friend, independent unemployed mechanic working on his own. I was then advised that if anything "went wrong", etc., this could create a bad situation (for me) as there would be no liability/responsibility for anything that might happen.  After contemplation, I decided best way to go would be where I could get a warranty on work (parts and labor), so got a shop estimate of $630 with same parts. Mazda dealer quoted $900, but after hearing previous estimates, convinced me to bring car in for them to check and they would work with me, convincing me they could get cost down to at least mid-$700s or probably even lower. Another shop quoted $260 labor plus cost of genuine Mazda parts which should make total around $700 +/-.  Took car into dealer, they tell me I don't need tensioner (would save about $65 for Mazda part per online research), added additional belts bringing total for parts/labor to $770 and intake "boot" (can't find this online - is it same as valve?) for 85.78/no additional labor, now back up to original $900 quote (actually $932.78 with taxes).  I do feel warranty is important as I cannot afford to put out more money for re-repair and have no other means of transportation. Do you know if Mazda parts carry their same warranty if service not done by a Mazda dealer/mechanic? I have owned Mazdas for several years now, but this is highest mileage and most major work at one time that I have ever had done on one, so I guess that is what is causing me the most stress, but would really appreciate your opinion.  I can't get a definitive answer on what they are charging for labor (as they tell me it varies from $95/hour, but less than that for this type work), but it seems that is the major cost difference, appearing to be (from quote of $260 of other shop) to what appears to be closer to $500 with Mazda, and they tell me they have worked to get the price down and are basically "cutting me a deal"?? Am I getting a good or reasonable deal for the work listed?  Two more things they found that will need replacing soon are a thermostat gasket (quoted $225) and distributor cap which is leaking minimal oil now (quoted $150). I was also told by them that my car is in extremely good condition for age/miles.  Do these prices sound reasonable too? Thank you so very much for your opinion/advice!!! 
|
|
|
|
|
Replying to: kaymt (Jul 25, 2008 3:54 am) I think genuine Mazda parts would have a warranty no matter who installed them but you'd have to demonstrate defects is materials and workmanship, and of course the LABOR is not warrantied by Mazda if an outsider installs the part. I know some very good indie shops so I'd be inclined to save the $300 and go there rather than the dealer, but if you don't have strong confidence in the indie shop or any idea of their reputation, then the dealer is really your only logical choice. |
|
|
Replying to: paramount13 (Jul 21, 2008 9:22 pm) |
|
I have a 94 protege 194k miles dx automatic. I have had this car for about 3 months and it has been great...until I parked it one night and when i got up the next day and cranked it it was sputtering and knocking it will not idle and when i try to drive it there is no power. If I put it in park and floor the accelerator it will only go to about 3500 rpm(still sputtering) and almost sounds like it is flooding.When I got the car I put new plug wires,plugs,dist cap and rotor button on it and accessory belts. I am disabled and only drive the car about 20 miles a week. I thought it may be fuel filter so I replaced it and removed the injectors and cleaned them still the same problem...help please,thanks.
|
|
|
|
|
Replying to: kenjen (Jul 26, 2008 2:42 pm)
|
|
|
Replying to: Mr_Shiftright (Jul 30, 2008 9:33 am)
|
|
|
|
|
Replying to: kenjen (Jul 30, 2008 9:54 am) You might have to cruise the specialty Honda internet sites to get this flash code information, or buy the proper workshop manual that tells you how, but you need some hard data to figure out what to do next. You can't just be throwing parts at it, that's expensive and frustrating. Your public library might have something.
|
|
You are here:
Forums
Sedans Mazda Protege Mazda Protege Maintenance and Repair
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2003 Mazda Protege
Browse by Board
Browse by Topic
Today's Chats
