You are here: Forums SUVs Chevrolet Blazer Chevy Blazer GMC Jimmy Maintenance and Repair

Chevy Blazer GMC Jimmy Maintenance and Repair

3449 messages,  Last post on Nov 07, 2009 at 8:55 AM

You are in the Chevrolet Blazer Forum. Your Hosts are steve_ & tidester

What is this discussion about? Chevrolet Blazer, GMC Jimmy, SUV

Messages Page 330 of 346 1 ... 327 328 329 330 331 332 333 ... 346 Prev Next Last

Go To Msg # Search This Discussion

#3283 of 3449 Re: Blower Directional Issues [pawlakjl] by 20blazer00 Sep 29, 2008 (6:32 pm)
Replying to: pawlakjl (Apr 14, 2008 9:07 pm) +This may be too late but just read this post. As I work for a car rental comp. We see this all the time. The main 2 reasons this happens is the cable that drives the door is loose, broken, or unattached. 2nd, is the control head itself.
#3284 of 3449 Re: Programming a new remote [20blazer00] by johnss10 Oct 01, 2008 (8:04 pm)
Replying to: 20blazer00 (Sep 26, 2008 10:20 pm) yes, there is a procedure to enter programming mode, using just the ignition switch. I used it to reprogram the 2 used remotes I bought off the net, I won't be able to look for it until the weekend. If I find it I'll let you know,
#3285 of 3449 Re: Speakers [rushfan1] by johnss10 Oct 01, 2008 (8:10 pm)
Replying to: rushfan1 (Sep 27, 2008 1:19 pm) The dash speakers are tiny. like 2 inches, with a big bracket. If you look on ebay for used blazer speakers, you'll probably find a picture. I haven't found any aftermarket speakers that will fit.
#3286 of 3449 Re: Programming a new remote [20blazer00] by impalacab Oct 01, 2008 (9:13 pm)
Replying to: 20blazer00 (Sep 26, 2008 10:20 pm) Hi, This is the procedure to program the remote: 1. Close all vehicle doors.  2. Insert the key into the ignition. 3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9. 4. Perform steps 5 through 8 in fairly rapid succession. 5. Turn the ignition switch to the ON position (as far as you can go without starting the engine). 6. Turn the ignition switch to the OFF position. 7. Turn the ignition switch to the ON position. 8. Turn the ignition switch to the OFF position. 9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically. 10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.   11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).  12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode. I have done it to get more than one transmitter to my Blazer, and it works. Good luck, Magnus, Sweden. Replies to this message: olddave (Oct 29, 2008 8:31 pm)
#3287 of 3449 Front axle won't engage on 4wd. by impalacab Oct 01, 2008 (10:03 pm)
I can't get the front axle to engage when changing into 4wd. I have checked the relays, they work. The switch work, and when pressing 4HI when driving, you can feel it engage. 4LO changes the transmission into low gear, but still not 4wd. When raising the vehicle and go to 4wd, the drive shaft to the front axle start to rotate as well. The vacuum actuator under the battery tray works and pulls the wire real strong. But the front wheels still wont rotate. I think the problem must be inside the front axle!? Do anyone have any suggestions? Please help, I need the 4wd when the snow start to fall. 1998 Blazer LT Replies to this message: adamg70 (Feb 20, 2009 4:35 am) impalacab (Feb 20, 2009 5:32 am)
#3288 of 3449 Re: Programming a new remote [20blazer00] by 20blazer00 Oct 02, 2008 (3:51 pm)
Replying to: 20blazer00 (Sep 26, 2008 10:20 pm) Ok, after some digging, and twisting arms and pulling hair, I finally got told the deal as to why my new remote wouldnt program. As it turns out, it does have to do with the after-market alarm. Its a GM after market alarm, and the old remote was for it. But, now for the bad part, that remote and its replacement are no longer made. It took a Chevy Parts man 4 hours to figure everything out. I went to places where alarms are sold and put in. About 15 of them and it was like, they just stared at me like I had something wrong with me. Came home and searched online remote outlets like keylessride and the like and still no luck. One gu told me I could just search for the FCC number instead of the P/N. But would that work? Find one that ues the same freq range? Replies to this message: jlflemmons (Oct 03, 2008 5:15 am)
#3289 of 3449 Re: Programming a new remote [20blazer00] by jlflemmons Oct 03, 2008 (5:15 am)
Replying to: 20blazer00 (Oct 02, 2008 3:51 pm) Did the vehicle originally have remote keyless entry installed at the factory? Look on the white tag in the glove box for the code AU0.   AU0 : LOCK CONTROL, REMOTE ENTRY – KEYLESS ENTRY (DOMESTIC)   If the vehicle had this installed at the factory, the OEM key fob for that year model would work.   I even took my 2002 which did not have RKE originally, installed the receiver (harness is already there, just plugs in above the parking brake), ordered a couple of fobs, had the dealer "tell" the body control module that the RKE was there, programmed the fobs, and voila, everything works perfectly.
#3290 of 3449 Re: Programming a new remote [20blazer00] by 20blazer00 Oct 04, 2008 (11:53 am)
Replying to: 20blazer00 (Sep 26, 2008 10:20 pm) no, It didnt come with one. Thats why it has what they call a dealer installed alarm or remote system. There for It has a remote that they put with it. ANd since I didnt have it put in, it was in when I bought it, I have no Idea which dealer did. So, Im out of luck there.I guess I could go to a dealer and get another put in to replace this one. Or just get a viper or another brand put in.  I did hear about buying the chip and box to have remote working, but, how much is it and how hard is it to install?
#3291 of 3449 Re: Heater won't work in our 1998 chevy blazer [pribylcrew] by sealteam8 Oct 04, 2008 (10:01 pm)
Replying to: pribylcrew (Jan 14, 2007 5:59 pm) The 02 sensor has nothing to do with the heater. Either the thermostat doesnt work or it could be low on antifreeze. As well as the heater core might be cracked. ANy smell of antifreeze in the cab of the truck? If not check the thermostat...
#3292 of 3449 parking brake release broken by brian352chevy Oct 05, 2008 (3:58 pm)
my parking brake release is broken on my 1998 4 door chevy blazer.the parking break is stuck on any idea on how to take it off with out the release handle

Messages Page 330 of 346 1 ... 327 328 329 330 331 332 333 ... 346 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums SUVs Chevrolet Blazer Chevy Blazer GMC Jimmy Maintenance and Repair