- #350 of 511
-
Re: HEATER-A/C problems [crazybob]
by hstachowski
-
Mar 09, 2006 (9:39 pm)
-
|
|
Replying to: crazybob (Jan 18, 2006 2:16 pm)
I have the exact same problem and mine starts to cycle hot/cold but then it stays hot and it is very hot. This is a 1998 Blazer S10 with the ECC. Did anyone solve this problem yet? Thanks I have not seen a answer to this yet other than going back to the stealer dealer to diagnose for big bucks.
|
- #351 of 511
-
Re: 95 GMC Jimmy 4WD - Unable to open rear hatch [pino5]
by raynbyrd
-
Mar 14, 2006 (12:35 pm)
-
|
|
Replying to: pino5 (Jan 21, 2006 5:09 pm)
done that, on a 1995 Blazer, I had to take off the inside panel to release the latch, a link inside the door had 1 end broken off, so the solenoid would pulse but on the other end, no action, i rigged the broken end of the link with a screw, works fine now, also drilled a small emergency hole in the inside panel so i wouldn't have to struggle to remove the panel again if i needed to repair it again
|
- #352 of 511
-
Re: 95 GMC Jimmy 4WD - Unable to open rear hatch [raynbyrd]
by mjacks
-
Mar 19, 2006 (9:13 am)
-
|
|
Replying to: raynbyrd (Mar 14, 2006 12:35 pm)
I have an '03 blazer and a friend slammed the rear so hard the plastic piece broke. someone did get it opened but now I can't and have followed all of these tips. please help. I have the emergency release area opened and can get it to move but not sure what to do. driving me crazy!
|
- #353 of 511
-
Re: Turn Signal Constant Clicking! [makpiette]
by izecold
-
Apr 14, 2006 (1:43 pm)
-
|
|
Replying to: makpiette (Dec 15, 2005 6:03 am)
Hello, I was reading your message and was wondering if you ever fixed the problem on your blazer? My 1999 blazer is having the same problem, it's really anoying. please help....
thanks
|
- #354 of 511
-
Re: Physco Turn Signal [makpiette]
by izecold
-
Apr 14, 2006 (1:49 pm)
-
|
|
Replying to: makpiette (Dec 12, 2005 7:27 am)
have u found a fix for your physco turn signal? Mine is doing the same thing!
|
- #355 of 511
-
Re: GMC Jimmy - Problems..Problems..Problems [crod59701]
by blazerblues1
-
Apr 24, 2006 (12:06 pm)
-
|
|
Replying to: crod59701 (Mar 01, 2001 9:16 pm)
Sorry, no clue about your problem. Although we are in the same boat about never buying a chevy again. My Blazer is an 87 and it doesn't go above 45 mph. EVER. I hear different reasons why that is but still haven't figured out the problem, but i just wanted to let you know i feel your pain. NEVER again.
|
- #357 of 511
-
Ok, here's the deal
by blazerblues1
-
Apr 24, 2006 (12:12 pm)
-
|
|
I have a 1987 Chevy Blazer with a 2.8 V6 that never goes above 45mph. I have to take back roads wherever i go. I heard it was the kickdown cable on the tranny, had that adjusted. i heard it was the injectors so i got some injector cleaner and that didn't work. I put good 93 octane gas and that didn't work. Any ideas? I don't think it's the tranny, i think it's the motor. I just don't know what part of the motor is screwing up. If anyone has had this problem or knows how to fix it without breaking the bank PLEASE let me know. I am mechanically inclined and have worked on many cars fixing many problems. i just need instructions on what to do and what the problem is.
|
- #358 of 511
-
Re: Ok, here's the deal [blazerblues1]
by firemankelly
-
Apr 29, 2006 (1:33 pm)
-
|
|
Replying to: blazerblues1 (Apr 24, 2006 12:12 pm)
Fire that baby up, walk around to the the back of it and check the flow from your exhaust. Could be a plugged catalytic converter or muffler. Keep on Blazin. Kelly
|
- #359 of 511
-
Rod Knock
by je101787
-
May 04, 2006 (3:01 pm)
-
|
|
I have a 1993 GMC Jimmy and it has a rod knocks in the engine. i was told it could be the lifters. I was wondering if anyone knew how long it would take to replace them cause i know you have to take the engine apart.
|
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
SUVs 
