You are here: Forums SUVs Ford Explorer Ford Explorer Maintenance and Repair

Ford Explorer Maintenance and Repair

6241 messages,  Last post on Nov 24, 2009 at 9:06 AM

You are in the Ford Explorer Forum. Your Hosts are steve_ & tidester

What is this discussion about? Ford Explorer, Mercury Mountaineer

Messages Page 619 of 624 1 ... 616 617 618 619 620 621 622 ... 624 Prev Next Last

Go To Msg # Search This Discussion

#6181 of 6241 Re: 2000 Ford Explorer ball joint replacement [bullridingfool] by egyptgerry May 15, 2009 (2:13 pm)
Replying to: bullridingfool (May 15, 2009 1:28 pm) I have the v6 but the ball joints are the same i think,the left and right are the same ball joint,Not sure how it says to replace the control arm,is there a nut about 4inches in from the ball jont on the control arm,if there is then you only need to replace the ball joint,Also if there is dont forget to count the turns when taking them of so that when you replace them you dont have to take the truck to have the tracking done,
#6182 of 6241 Re: 2000 Ford Explorer ball joint replacement [bullridingfool] by bioman May 15, 2009 (3:15 pm)
Replying to: bullridingfool (May 15, 2009 1:28 pm) For the upper ball joint the upper control arm and the ball joint has to be replaced. They are an integrated unit. For the lower ball joints you can replace just the ball joint not the entire control arm. The lower control arm and ball joint take must of the weight and abuse.
#6183 of 6241 wrong 02 sensor used by bbelasco May 26, 2009 (6:33 am)
Hello, I replaced an o2 sensor from a 1998 awd 5.0 befor cat passenger side with an o2 sensor from a ford escape, yes dumb idea. Upon driving i noticed a sulfer smell, only drove it about 5 miles. immediatly replaced it with a new correct one. Rotten egg smell gone, but now car runs rough, what did I screw up? help!
#6184 of 6241 1999 Explorer hood by swburbguy Jun 11, 2009 (11:18 am)
I cant get my hood to open on my explorer? Anyone have any ideas?
#6185 of 6241 1999 explorer by swburbguy Jun 11, 2009 (11:28 am)
MY explorer o/d light comes on sometimes. Whats causing this?
#6186 of 6241 pcv replacement by pfran6078 Jun 17, 2009 (11:43 am)
can anyone tell me on how to replace the pcv valve on a 2000 explorer 5.0 engine Replies to this message: electricdesign (Jun 21, 2009 6:31 pm)
#6187 of 6241 atwitsend by wizard43 Jun 19, 2009 (11:19 am)
i have a 2000 ford explorer,it will start early in the morning run for about 30-40 secs. then dies out and will not run for longer than 3 are 4 secs i changed out the fuel pump and it still does the same thing .ive checked the filter its clear.
#6188 of 6241 Re: power window [electricdesign] by racheys Jun 19, 2009 (6:18 pm)
Replying to: electricdesign (Apr 26, 2006 3:30 am) I had the same prob with my 91 ,I bought the gear for the front but the back is not available ...you have to replace the whole motor.After thinking about it for a while I had a great idea , why not get epoxy resin and mix it up and use that to replace plastis that crumbles , well I did, both the back windows now work like new and it saved me $150.00
#6189 of 6241 Re: pcv replacement [pfran6078] by electricdesign Jun 21, 2009 (6:31 pm)
Replying to: pfran6078 (Jun 17, 2009 11:43 am) See message #6171 for location of the pcv. You can't see it, but you can feel for it, and pull it out, and replace it by feel.
#6190 of 6241 atwitsend by wizard43 Jun 22, 2009 (5:05 am)
pvc valve is good, got a po320 code from scanner, so im thinking maybe the coil pack is bad since it is distributerless Replies to this message: electricdesign (Jun 22, 2009 10:54 am)

Messages Page 619 of 624 1 ... 616 617 618 619 620 621 622 ... 624 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums SUVs Ford Explorer Ford Explorer Maintenance and Repair