Last post on Oct 26, 2013 at 4:56 AM
You are in the Ford Explorer
What is this discussion about?
Ford Explorer, Mercury Mountaineer
Go to NHTSA to file a safety complaint.
Or call Monday-Friday (8 am to 8 pm ET) (888) 327-4236 TTY: (800)424-9153
#4021 of 6400 Lights Spontaneously Flashing and Draining Battery
Jul 12, 2005 (6:44 am)
I have a Ford Explorer Sport 1999 with 120,000 km. Last week I discovered that the parking lights turn on by themselves for short periods during the night. This happens when the vehicle is parked and the keys are not in. I suspect some sort of shortcut. The result is, some mornings I have to get a battery boost from someone else because the lights have drained the power.
I talked to a few mechanics and no one seems to know where the problem is. Any sort of help will be greatly appreciated. Thanks in advance.
#4022 of 6400 plug fouling
Jul 12, 2005 (7:52 am)
I have a 1998 Explore 4x4 6 cyl. My number 3 plug fouls often (these are platinum plugs)...... any ideas out there?
#4023 of 6400 Re: 2003 4X4 Explorer with Grinding Noise When Accelerating [jsomma]
Jul 12, 2005 (2:28 pm)
I have a 2002 4x4 explorer and i am hearing some grinding noises when i excellerate too. I am really nervous cuz I just baught it and dont have the money to fix something huge yet. If anyone has the answers i would really appreciate it!
#4024 of 6400 Re: plug fouling [ogbonna]
Jul 12, 2005 (2:37 pm)
Describe what your fouled plug looks like. Black, gray, oily, dry, etc.
#4025 of 6400 Re: plug fouling [ogbonna]
Jul 13, 2005 (3:33 am)
How long does it take for the plug to foul when a new one is put in? Is the color dry black (too rich), or wet black (oil) or other? Do a compression test on the engine and compare compression between cylinders, there should be no more that 20% variation. Low compression could indicate a problem in the rings, head gasket, head or valves.
Let us know what you find out.
#4026 of 6400 I NEED HELP RE: CLUTCHES
Jul 13, 2005 (10:03 am)
Hi.. 3 days ago my son purchased a 1992 ford explorer (stick). He had 3 driving lessons in it totalling a little over 2 hours worth... I drove it the remaining times. The clutch went on the 3rd day. mechanic says the clutch was new... put in two years ago to this day... and a little over 20,000 miles put on it.... my question is this... could we possibly have destroyed a clutch in less than 3 days of driving around town? He seems to be blaming this problem on my son not knowing how to properly drive a stick... but i was with him each of the 3 times he was out learning and KNOW he didn't ruin the clutch....(and i KNOW i didn't either) .... any one have any ideas???? think it's going to be a battle trying to get the $1,700 back that we paid for it... everyone i've talked to says there's no WAY he could have destroyed a clutch in such little time... anyone have this problem???
#4027 of 6400 I NEED HELP RE: CLUTCHES by hiskris
Jul 13, 2005 (11:08 am)
It depends on how the clutch failed.
If the friction material or pressure plate has been scattered, this can occur easily by selecting too low a gear when downshifting. Clutch doesn't even have to be engaged. If first gear is engaged in the transmission when fourth was intended, the clutch will over-rev & possibly self-destruct.
If the friction material is worn out or burned up, that's another story. I can destroy a clutch in less than an hour. But, it sounds like you were with the vehicle all the time & didn't observe excessive clutch slipping.
So, if you're sure neither of the above circumstances occurred, you're probably right. However, even the auto manufacturers cinsider the clutch a wear item with a wear rate much dependent on driver habits. After 2 years & 20,000 miles, I doubt that there's a service shop on the planet that would give you a free replacement.
I suspect that the clutch was on its last legs when you bought the vehicle. A more thorough inspection & evaluation might have saved you a lot of grief & $$.
FWIW, I think the mechanic is way off base trying to blame your son.
#4028 of 6400 Re: Rear Door Hatch Hinges [shan4]
Jul 13, 2005 (3:21 pm)
I have a similar problem with a 1998. I just doesn't close well. eventually it got so bad that It wouldn't close at all. Had the hinges replaced and reinforced, but the problem is coming back. I would be interested to hear if you find out anything.
#4029 of 6400 Re: I NEED HELP RE: CLUTCHES [hiskris]
Jul 13, 2005 (6:08 pm)
my wife had a '91 explorer with a manual transmission. she had it for 83k. it still had the original clutch. i would agree that it would be difficult to destroy a clutch in so few miles. another thing that comes to mind is that one time i pulled a friends astro minvan and their 19 foot boat up a boat steep ramp after they couldn' get up out of the water. the clutch smelled really bad for a few minutes, but we drove it for several years after that with no problem.
#4030 of 6400 remanufactured half shaft leaking at differential axle seal
Jul 13, 2005 (6:17 pm)
I cut a boot on my CV joint, so I installed a remanufactured left Half Shaft (Cardone 60-2101) and a new axle seal (National 710429, which matches the OEM seal exactly) into my 97 Mountaineer. Now the axle seal leaks. The remanufactured axle journal fits very loosely into the axle seal. The journal measures 1.401 inches. Does anyone know what a Ford left half shaft axle journal measures (I had to return my OEM shaft for the core)? A brand new Cardone left Half Shaft measures the same as the Cardone remanufactured.
Thanks for the help... if the OEM journal is larger than 1.401, I'll have to order up a Ford OEM shaft ($200 vs the $60 for the remanufactured).